Bedienungsanleitung Bresser 7902510 Weather Center 5-in-1 (Seite 13 von 20) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

771276

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

next setting.

3. Repeat step 2 for setting hours, minutes, seconds, year, month, date,

hour offset, language and daylight saving time (DST).

NOTE!

1. The unit will automatically exit setting mode if no button was pressed

in 60 seconds.

2. The hour offset is for DCF and MSF version. Its range is between -23

and +23 hours.

3. The language options are English (EN), French (FR), German (DE),

Spanish (ES), and Italian (IT).

4. DST (Daylight Saving Time) feature is set to Auto (factory set). The

clock has been programmed to automatically switch when the daylight

saving time is in effect. User can set the DST to OFF to disable the

feature.

Disable / Enable RCC signal reception (Fig. 12)

1. Press and hold RCC button 8 seconds to disable the reception.

2. Press and hold RCC button 8 seconds to enable automatic RCC

reception.

Fig. 22

RCC signal on RCC signal off

ALARM CLOCK SETTING

Turn on/off alarm clock (and ice-alert function) (Fig. 13)

1. Press button to show the alarm time.

2. Press button twice to activate the alarm.

3. Press button three times to activate alarm with ice-alert function.

4. To disable the alarm, press button until the alarm icons disappear.

Fig. 23

Alarm off Alarm on Alarm and ice-alert on

NOTE!

1. Press SNOOZE/LIGHT button when alarm sounds to interrupt the

alarm. The alarm will then start again after 5 minutes.

2. Pres button when alarm sounds to deactivate the alarm until next

time.

Alarm time setting

1. Press and hold button for 2 seconds to enter alarm setting mode.

Hours will begin to flash.

2. Use or button to adjust the desired value and press button

to proceed to set minutes.

3. Repeat step 2 to set minutes, then press button to exit.

NOTE!

Press button twice when alarm time is being displayed will activate

the temperature-adjusted pre-alarm (ice-alert). The alarm will sound 30

minutes earlier if it detects outside temperature is below -3°C.

WEATHER FORECAST

The device contains sensitive pressure sensor built-in with sophisticated

and proven software that predicts weather for the next 12 hours.

sunny, clear slightly cloudy cloudy rainy rainy, stormy snowy

Fig. 24

NOTE!

1. The accuracy of a general pressure-based weather forecast is about

70% to 75%.

2. The weather forecast is meant for the next 12 hours, it may not

necessarily reflect the current situation.

3. The “Snowy” weather forecast is not based on the atmospheric

pressure, but based on the outdoor temperature. When the outdoor

temperature is below -3°C (26°F), the “Snowy” weather indicator will

be displayed on the LCD.

4. The icon will flash on the screen when the rainstorm comes.

BAROMETRIC / ATMOSPHERIC PRESSURE

Atmospheric Pressure is the pressure at any location of the Earth caused

by the weight of the column of air above it. One atmospheric pressure

refers to the average pressure and gradually decreases as altitude

increases. Meteorologists use barometers to measure atmospheric

pressure. Since variation in atmospheric pressure greatly affected by

weather, it is possible to forecast the weather by measuring the changes

in pressure.

Select display mode

1. Press and hold button for 2 seconds to enter atmospheric pressure

setting mode.

2. Use or button to select between absolute and relative

atmospheric pressure:

• ABSOLUTE the absolute atmospheric pressure of your location

• RELATIVE the relative atmospheric pressure based on the sea level

Set relative atmospheric pressure value

1. Get the atmospheric pressure data of the sea level (it is also the

relative atmospheric pressure data of your home area) through the local

weather service, internet and other channels.

2. Press and hold button for 2 seconds until ABSOLUTE or RELATIVE

flashes.

3. Press or button to switch to RELATIVE mode.

4. Press button again and the number for RELATIVE flashes.

5. Use or button to change the value.

6. Press button to save and exit the setting mode.

NOTE!

1. The default relative atmospheric pressure value is 1013 mb/hPa

(29.91 inHg), which refers to the average atmospheric pressure.

2. When you change the relative atmospheric pressure value, the weather

indicators will change along with it.

3. The built-in barometer can notice the environmental absolute

atmospheric pressure changes. Based on the data collected, it can

predict the weather conditions in the forthcoming 12 hours. Therefore,

the weather indicators will change according to the detected absolute

atmospheric pressure after you operate the clock for 1 hour.

4. The relative atmospheric pressure is based on the sea level, but it

will change with the absolute atmospheric pressure changes after

operating the clock for 1 hour.

Select barometer measurement unit

Press button several times until the desired measurement unit is

displayed: inHg, mmHg or hPa.

TEMPERATURE & HUMIDITY

Comfort Indication

The comfort indication is a pictorial indication based on indoor air

temperature and humidity in an attempt to determine comfort level.

Fig. 25

too cold, too dry comfortable too warm, too humid

HINWEIS!

1. Comfort indication can vary under the same temperature, depending

on the humidity.

2. There is no comfort Indication when temperature is below 0°C (32°F)

or over 60°C (140°F).

Bresser 7902510 Weather Center 5-in-1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7902510 Weather Center 5-in-1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info