Bedienungsanleitung Bresser 9070710 VA colour LCD - National Geographic (Seite 21 von 52) (Deutsch, Englisch, Französisch, Spanisch)

785323

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

21 / 52

8. Wait until the indoor temperature is displayed on the base station.

NOTICE!When switching from mains power supply to battery power supply or vice versa,

the power supply is being disabled for a short moment for technical reasons. Exception: per-

manent battery operation.

Remote sensor

9. Remove the battery compartment cover.

10. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

11. Set the channel selector switch to the desired channel.

NOTICE!This weather station can be operated with one or more remote sensors. Each re-

mote sensor being connected must be operated on a different channel. If only one remote

sensor is connected, it should be operated on channel 1.

12. Replace the battery compartment cover.

10 Automatic time setting

After the power is restored, the unit automatically searches for the radio signal. It takes approximately

3-8 minutes for this process to complete.

If the radio signal is received correctly, the date and time are set automatically and the reception sym-

bol is displayed.

NOTICE!Some functions/buttons are deactivated during radio signal reception.

If no radio signal is received, proceed as follows:

1. Press the UP button on the base unit for approx. 3 seconds to activate reception of the radio sig-

nal. Reception is now initialized again.

2. If still no radio signal is received, the time must be set manually.

11 Manual time setting

To set the time/date manually, first check whether the radio symbol in the display is still flashing (auto-

matic reception of the time signal is then still active). Now press the UP button for approx. 3 seconds

to deactivate reception.

1. Press the SET button for approx. 3 seconds to enter the time setting mode.

2. Digits to be set are flashing.

3. Press UP or DOWN button to change the value.

4. Press the SET button to confirm and switch to the next setting.

5. Sequence of the settings: Hours > minutes > year > day/month, month/day > month > day > air

pressure unit > exit

6. Finally, press the SET button to save the settings and exit settings mode.

12 Alarm setting

1. Press the ALARM button to display the alarm time.

2. Press the ALARM button for approx. 2 seconds to enter the alarm time settings mode.

3. Digits to be set are flashing.

4. Press UP or DOWN button to change the value.

5. Press the ALARM button to confirm the entry and move to the next setting.

6. Sequence of the settings: Hours > minutes

7. Finally, press the ALARM button to save the settings and exit the setting mode.

8. In normal display mode, press the ALARM button to display the currently set alarm time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 9070710 VA colour LCD - National Geographic Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 9070710 VA colour LCD - National Geographic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info