Bedienungsanleitung Bresser 96-18760 - Skylux 70-700 (Seite 13 von 66) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

664376

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

- 13 -

General Information

About this Instruction Manual

Please read the safety instructions in this manual carefully. To

avoid damage to the unit and the risk of injury, only use this

product as described in the manual.

Keep the instruction manual handy so that you can easily look

up information on all the functions.

DANGER!

You will find this symbol in front of every section

of text which deals with the risk of severe injury

or even death in the event of improper use.

CAREFUL!

You will find this symbol before every section of

text that deals with the risk of minor to severe

injuries resulting from improper use.

NOTE!

You will find this symbol in front of every section

of text which deals with the risk of damage to

property or the environment.

Intended Use

This product is intended only for private use.

It was developed for the magnified display of things in nature.

General Warning

RISK of bodily injury!

Never use this device to look directly at the sun

or in the direct proximity of the sun. There is a

RISK OF BLINDNESS!

Children should only use the device under adult supervi-

sion. Keep packaging material (plastic bags, rubber

bands, etc.) out of the reach of children! There is a RISK

OF CHOKING!

FIRE RISK!

Do not place the device — in particular the lenses — in

direct sunlight. The concentration of light could cause

fire.

RISK of property damage!

Do not disassemble the device. In the event of a defect,

please contact the Service Centre in your country.

Do not expose the device to temperatures above 60°C.

Privacy PROTECTION!

The binoculars are intended only for private use.

Please heed the privacy of other people - do not

use them to look into apartments, for example.

All parts (Fig. 1-3)

B Telescope tube

C Viewfinder scope

D Adjusting-screws (viewfinder)

E Tube opening

f Objective

g Eyepiece connection

H Focus wheel

I Tube rings

J Tripod head (mounting)

1) Accessory tray

1! Adjusting-screws (tripod)

1@ Fixing bracket (accessories tray)

1# Tripod legs

1$ Flexible shaft for elevation adjustment

1% Flexible shaft for azimuth adjustment

1^ Tripod brace

1& Latitude adjustment

1* 2 eyepieces (Ø 31.7mm / 1 ¼”) f=20mm, f = 4mm

1( Star diagonal prism

2) Erecting lens 1,5x

2! Barlow lens 3x

2@ Smartphone holder

Parts (Fig. 15): Mounting

A Vertical clamp

B Incline plate

C Declination axis

D Flexible adjustment shaft

E Flexible shaft (declination axis)

F Focussing wheel

Part I – Setup

1. General/Location:

Before you begin construction, you must choose a suitable

location for your telescope.

It will help you, if you build this appliance in a place, where you

have a clear view of the skies, a stable footing and sufficient

space around you.

Remove all the parts from the packaging first. Check, using the

diagram, whether all the parts are there.

NOTE!

Important: Only da the screws up finger tight

and avoid over tightening them.

2. Setup - tripod

The tripod legs are pre-installed and already connected to the

tripod head (illustration 5, X) and tripod spider (illustration 1, 16).

Remove the tripod from it’s packaging and place it upright with

the feet at the base. Take two of the legs and carefully pull them

apart until they are in the fully open position. The entire weight

of the tripod rests on one leg during this procedure. Then set

the tripod upright again.

The entire tripod weights rests on one leg here. Then set the

tripod upright again. Now extend each individual tripod leg to the

desired length (see illustration 4) and undo the fastening clips for

this purpose (illustration 1+4, 11) (total of 3). Tighten the fasten-

ing clips and place the tripod on a hard flat surface.

HINT!

A small spirit level, placed on the accessory tray,

may help you to setup you telescope in level.

3. Setup – accessory tray:

Three accessories tray (illustrations 1, 3, and 10) is inserted with

the flat side down centrally on the tripod spider (illustration 1, 16)

and mounted in place by turning clockwise once (60°) (illustration

5). The three fittings of the accessories tray must be aligned with

the tripod spider retaining fittings and fixed in place by them.

4. Setup – tube:

To mount the telescope tube (Fig. 1, 1) you undo the screw on

the tube ring (Fig. 6, X) and open up the ring.

Now you place the tube in the centre of ring and close the ring

up. Now secure the mounting by tightening the screw.

Place the tube including clip with the objective opening facing

north on the mounting. Fasten the tube holder using the clamp-

ing screw to the mount head (illustration 7).

5. Setup – eyepiece:

Your telescope is equipped with two eyepieces (Fig. 1+2, 18)

and a star diagonal (Fig.1+2, 19) as part of the basic equipment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 96-18760 - Skylux 70-700 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info