Bedienungsanleitung Bresser Messier Exos 2 (Seite 8 von 44) (Englisch)

784595

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Looking at or near the Sun will cause instant and irreversible damage to your eye!

Assembling

(EXOS-1 mount on ST-1 tripod)

Telescope Assembly

As you unpack your telescope, carefully note the following parts. The

assembly is shipped in separate boxes.

• Equatorial mount with polar alignment finder

• Heavy duty, adjustable steel tube tripod with leg braces, three tripod leg

lock knobs, and a captive mount locking knob

• Complete optical tube assembly including primary mirror with dust cover

and a rack-and-pinion focuser and eyepiece holders for both 1.25“ and

2“ eyepiece holders, tube cradle assembly with two rings and two lock

knobs

• Eyepiece

• Counterweight and counterweight shaft. Some models include an

additional counterweight.

• 8 x 50mm or 6 x 30mm viewfinder

How to Assemble Your Telescope

The giftboxes contain the optical tube assembly and the tripod with the

equatorial mount. The accessories are located within compartments cus-

tom-cut into the styrofoam block inserts.

instructions on telescope assembly. The packaging contains the main tube

and tripod components, the tripod with mounting and accessories.

1. Remove the components from the packaging and familiarise yourself

with them. Please refer to illustrations 1a to 1d for details of telescope

assembly. When removing the tripod from its packaging keep it parallel

to the floor as the inner legs may otherwise slide out as they are not yet

screwed tight.

2. Assembly - tripod: The tripod legs are preassembled and already con-

nected to the tripod head and accessory tray. Remove the tripod from

the packaging and place it in front of you, with the tripod legs on the

floor. Grab two legs and pull them apart until fully spread out. The tripod

weight rests only on one leg. Now level the tripod and adjust third leg

if necessary. Pull out the bottom part of the leg to the desired length

(Fig. 2b) and lock with the locking knob (3 pieces total) to a firm feel. Be

careful not to over tighten the screws! These screws lock the inner leg

segments to the desired tripod height.

3. Assembly - mounting accessory tray: The accessory tray (Fig.: 2a) Is

placed on the tripod spider with the flat side facing down, then locked in

place turning the tray approximately 60° clockwise. The three gudgeons

of the tray should be centered on the spider vanes and lock in place.

4. Assembly - installing the mount: position the mount on the tripod head

so that the nose on the tripod head meets the opening of the mount (Fig.

2e). Insert the central screw into the tripod head from the bottom and

screw the tripod head with the mount (Abb. 2e).

Fig. 2a: The tripod

Fig. 2b: tripod leg locks

Fig. 2c: Tripod head

assemblInG exos-1

Fig. 2d:

installing the mounting on

the EXOS-1 tripod.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser Messier Exos 2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser Messier Exos 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info