Bedienungsanleitung Bresser NT-130 (Seite 9 von 44) (Englisch)

611626

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Looking at or near the Sun will cause instant and irreversible damage to your eye!

5. Fastening the counterweight on the counterweight rod: insert the base

of the counterweight rod (20, illustration 1d) on the threaded end of the

rod and screw it on the counterweight rod (22, illustration 1). Then screw

both in the thread on the base of the declination axis and counter screw

rod to base. If you look through the large drill hole in the counterweight

you will see the bolt blocking the hole. Move the counterweight slightly

to make it disappear in its drill hole and reveal the hole. If it doesn‘t,

carefully loosen the counterweight screw until the bolt moves. Remove

the safety cover (23, illustration 1d) from the rod. Hold the counterweight

firmly whilst moving it to about the middle of the counterweight rod (22,

illustration 1d). Tighten the counterweight fastening screw and then

replace the safety cover.

NOTE:

If the counterweight ever slips, the safety cap (23, Fig. 1d) prevents the

counterweight from sliding entirely off the shaft. Always leave the safety cap

in place when the counterweight is on the shaft.

6. Set the latitude. Setting the latitude is easier if it is set before you attach

the optical tube to the assembly. Locate the latitude dial (28, Fig. 1d); note

that there is a triangular pointer above the dial located on the mount. The

pointer is not fixed; it moves as the mount moves.

Determine the latitude of your observing location. See APPENDIX B:

LATITUDE CHART, page 28-29, for a list of latitudes, or check an atlas.

Move the latitude T-handle screws in order to move the mount until the

pointer points to your latitude. The two T-handle screws (EXOS 2 only)

work in a „push - pull“ operation—as you tighten one, loosen the other.

When the pointer points at your latitude, tighten both screws until they

make contact with the mount.

At your observing site, set up the telescope assembly so that this leg

approximately faces North (or South in the Southern Hemisphere).

7. Attach the cradle assembly to the mount

–

Models R and N: Remove the

optical tube from the cradle and slide the cradle assembly (11, Fig. 1a)

onto the cradle mounting slot. See Fig. 2g. The rounded base of the cradle

assembly fits into the rounded portion of the mounting slot. Tighten both the

cradle locking knob and the secondary locking knob to a firm feel.

8. Position optical tube –

Models AR and NT:

Unscrew the cradle ring lock

knobs (13, Fig. 1a) and open the cradle rings. While firmly holding the

optical tube (10, Fig. 1a), position it onto the cradle rings (14, Fig. 1a)

with the mid-point of the optical tube’s length lying roughly in the center

of the cradle ring assembly. Point the tube so that the front end (this

end comes shipped with the dust cover (9, Fig. 1a) over it) is oriented

as depicted in Fig. 1a. Then close the cradle rings (14, Fig. 1a) over the

optical tube. Loosely tighten the cradle ring lock knobs just to hold the

tube securely in place until you balance it. See Balancing the telescope,

page 13.

Fig. 2h: Place the optical tube

in rings and loosely tighten the

cradle ring lock knobs.

Fig. 2g: Attach cradle to base mounting

and tighten locking (EXOS1)

Fig. 2f: Mounting the cradle (dovetail)

plate to the mount shaft (EXOS1)

as s e m b l I n G ex o s 1

Fig. 2e:

installing the mounting on

the Exos1 tripod.

Cradle

mounting

slot

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser NT-130 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info