Bedienungsanleitung Bresser NT-203 (Seite 21 von 44) (Englisch)

611628

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Looking at or near the Sun will cause instant and irreversible damage to your eye!

ma I n t e n a n c e a n d se r v I c e

IMPORTANT NOTE:

Do not force the 4 screws past their normal travel, and do not rotate any

screw or screws more than 2 full turns in a counterclockwise direction (i.e.,

not more than 2 full turns in their „loosening“ direction), or else the diagonal

mirror may become loosened from its support. Note that the diagonal mirror

collimation adjustments are very sensitive: generally turning a collimation

screw 1/2-turn will have a dramatic effect on collimation.

3. If the reflection of the diagonal mirror is not centered within the reflection

of the primary mirror, adjust the 3 collimation screws located on the rear of

the primary mirror cell.

NOTE:

There are 6 screws (Fig. 31c) on the primary mirror cell. The 3 knurled

knobs are the collimation screws, and the 3 smaller thumb screws are lock-

ing screws. The locking screws must be loosened slightly in order to adjust

the collimation screws.

Proceed by „trial and error“ until you develop a feel for which collimation

screw to turn in order to change the image in any given way.

4. Perform an actual star test to confirm the accuracy of steps 1 through

3. Using the 25mm eyepiece, point the telescope at a moderately bright

(second or third magnitude) star, and center the image in the main

telescope‘s field of view.

5. Bring the star‘s image slowly in and out of focus until you see several

disks surrounding the star‘s center. If steps 1 through 3 were done

correctly, you will see concentric (centered with respect to each other)

circles (1, Fig. 32).

An improperly collimated instrument will reveal oblong or elongated circles

(2, Fig. 32). Adjust the 3 collimating screws on the primary mirror housing

until the circles are concentric on either side of the focus.

In summary, the 4 adjustment screws on the plastic diagonal mirror housing

change the tilt of the secondary mirror so that it is correctly centered in the

focuser drawtube, and so that the primary mirror appears centered when

looking into the focuser. The 3 collimating knobs on the primary mirror

change the tilt of the primary mirror so that it reflects the light directly up the

center of the drawtube.

Inspecting the Optics

A Note About the “Flashlight Test: If a flashlight or other high-intensity light

source is pointed down the main telescope tube, the view (depending upon

the observer’s line of sight and the angle of the light) may reveal what

appears to be scratches, dark or bright spots, or just generally uneven coat-

ings, giving the appearance of poor quality optics. These items are only

seen when a high intensity light is transmitted through lenses or reflected

off the mirrors, and can be seen on any high quality optical system, includ-

ing giant research telescopes.The optical quality of a telescope cannot be

judged by the “flashlight test;“ the true test of optical quality can only be

conducted through careful star testing.

Laser collimator:

To make the collimation easier, a laser can be used to align the secondary

mirror and the main mirror. Especially fast Newtonians (f/5 or f/4 systems)

require precise collimation to deliver the best possible optical performance.

It is recommended, to check the collimation prior to every observing or

imaging session.A suitable laser collimator can be found with item number

4910200 in our product range. All Bresser Messier Newtonian telescopes

have a center marking on the main mirror so a laser can be used for col-

limation.

Fig 31b: The four collimation

screws on the secondary mirror

housing

Fig. 31c: The six collimation

screws on the rear of the primary

mirror cell.

knurled knob

thumbscrew

Fig. 32: Correct (1) and incorrect

(2) collimation viewed during a star

test.

1 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser NT-203 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info