753042
5
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
Art.-nr.: 611885-G
5
Connecting a Brink Excellent heat recovery (HRV) appliance to a Modbus network, for instance a building automation system (BAS),
requires an interface. This interface, called “Brink Connect”, allows communication between the Brink HRV appliance and a Modbus
network. The interface described here is only suitable for communication between a Brink HRV appliance with UWA control PCB (with
software version from S1.06.06) and a Modbus network. The interface comes with a 1,5 m long connecting cable for connecting the
"Brink Connect" to an Excellent HRV appliance.
Note: It is not possible to use a control unit, humidity sensor or multiple switch in combination with a Brink Connect interface on the
Brink HRV Excellent. If the Brink Connect is used exclusively for reading out values, the control module/Brink Air Control and multiple
switch can still be used.
The system does support an eBus CO
2
sensor (code 532196 - 4 sensors max.) that is connected to the HRV appliances.
If the Brink HRV-appliances are cascaded, the Brink Connect must be connected to the Master appliance.
General
Technical speci¿cations:
Appliance Interface %ULQN+59V¿WWHGZLWKD,&EXVFRQQHFWLRQFRQQHFWRU;RQ%ULQN8:$3&%'HOLYHU\
FRQ¿JXUDWLRQ02'%865786/$9(
Dimensions WxHxD Dimensions WxHxD 36 x 89.7 x 62.2 mm
Connection Connection through screw plug terminals up to 1.5 mm²
Housing Housing as per DIN 43880 for use in electrical distribution boxes (RAL 7035)
Weight Weight ca. 100 g
Storage temperature Storage temperature -10...+70 °C
Power consumption Power consumption 0.2 W
Relative humidity Relative humidity up to 85% without condensation VDE 0160, EN 50178, Class 3K3
Installation position Installation position on vertical surfaces (wall installation, connectors top and bottom)
Interfaces Interfaces 1 x RS485 / 1x I2C interface
Protection class Protection class IP 20
Power supply Power supply +5 VDC ±10 %
Module status display Power supply indication by green LED
System bus RS485
Ambient operating temperature +5...+40°C
Modbus Interface
Brink Connect (Interface module I2C<>Modbus) allows making a connection between an RS485 interface and an I2C interface. That
way products or installations that do not have a Modbus interface as standard can still be incorporated into a Modbus network using
a (free) I2C interface.
Application
Con¿guration %rinN Connect
The Brink Connect come with a default Modbus Slave address
11 ( 0x0B). Communication parameters Modbus:
 %DXGUDWH
 3DULW\HYHQ
 6WRSELWV
Connector no. Function
1 +5V system voltage
2 GND system voltage
3 I2C bus Serial Data (SDA)
4 I2C bus Serial Clock (SCL)
5 RS485 - A
6 RS485 - B
7KH3&%FRPHVZLWKWKHVWDQGDUG0RGEXVVODYHDGGUHVV7KDWDGGUHVVPXVWEHXVHGIRUWKH¿UVWFRPPXQLFDWLRQVHVVLRQ
Then a new Modbus slave address between 1 and 247 can be entered at register address 1000, using function code 0x06, write
single register When entered correctly, the Modbus slave address will directly be active.
The standard register address is 1000; Dependent on the program used, it may have shifted 1 step (999 or 1001). After chang-
ing the slave address, you must call up this address using function code 0x03 and then check whether the changed address is
correct. Then the power to the Brink Connect must be switched off. Now the slave address has been changed correctly.
pwr
1
+5V
2
GND
3
SDA
4
SCL
5 A
485
6 B
485
I2C <> Modbus
cdefgh
36
89,7
62,2
GB
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brink Connect wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info