Bedienungsanleitung Brink Evap (Seite 41 von 64) (Deutsch, Englisch, Holländisch, Französisch)

753040

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Evap 7

¹ See chapter 10 for version adjustment

Section 6 – Faults

When the control in the Evap detects a fault, this is displayed at the bottom of the product by the alarm symbol

(bell) by means of an LED. To reset the alarm the product must be briefly disconnected from the power supply by

removing the plug from the socket and then replacing this in the socket after 10 seconds. A TEST cycle of

approximately 3 minutes will start, during which the service LED flashes. The light stops flashing when the test is

over. The Table¹ below shows different causes of an alarm and the repair or control action.

Alarm LED

Meaning

Action

Reset

Alarm LED on

Contact System

On/Off broken,

unit switches off

Restore contact System On/Of, see wiring diagram

Automatic

Alarm LED blinks

3 times

Contact with

SHC80 sensor

broken

Check SHC80 wiring and if necessary repair, check that

the light on SCH80 sensor flashes regularly, if not replace

faulty sensor.

Automatic

Alarm LED blinks

5 times

T3 sensor

outside air faulty

Check wiring for break or wear, in case of doubt replace

sensor.

Automatic

Alarm LED blinks

9 times

There is no

increase in

channel RH%

(T1 SHC80), for

a period of 3

hours. The unit

turns off.

- Check if the water tap is open.

If the tap is open and there is a demand (outside

temperature below 12 ° C) check the strainer in the

connection coupling, it must be clean.

- Check the functioning of the water valve. Disconnect the

black supply hose from the knee on the unit, and reset

the unit by plugging out and plugging in again; if water

comes out and the water valve and this stops after 90sec,

then the valve is OK, the water keeps flowing or no water

comes out of the hose, then the water valve is defective,

replace the water valve. If the water valve works and the

matrix does not get wet after the valve has switched, the

legionella filter is clogged; replace the cassette.

If the matrix does get wet and still has an alarm, the

matrix is contaminated and the cassette must be

replaced. Product No .: 351025

Automatic

Alarm LED blinks

15 times

Heating faulty

Check air temperature after the humidifier, this must be

>8ºC, if not air heater is faulty. Call installer for

replacement.

Automatic

Alarm LED blinks

17 times

No airflow

Check if HRV is working. If this works, the matrix is

contaminated and must be replaced. Product No .:

351025

Automatic

Alarm LED blinks

19 times

T2 sensor faulty

Check wiring for break or wear, in case of doubt replace

sensor.

Automatic

Service LED

continuously on

The cassette

must be replaced

To be able to humidify safely it is necessary to

replace the complete cassette; Order product code

351025 from your dealer.

In the interim, you can reset the service alarm at the

bottom by pressing and holding the reset button for

30 seconds. The opening is located next to the

service LED.

ATTENTION the LegioSafe filter will soon become

obstructed, after which proper and safe operation is

no longer guaranteed!!

Reset the service alarm

at the bottom by

pressing and holding the

reset button for 30

seconds. The opening

is located next to the

service LED.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brink Evap Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info