Bedienungsanleitung Brinno MAS200 (Seite 2 von 2) (Englisch)

785786

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

3 4

8 9

Specications

Delete Sensor

Transmission/Detection

7Pairing Channels

Multiple Sensors

MAS200

90° (horizontal)

Centerline: 13 ft (4 m)

Side: 5 ft (1.5 m)

32 ft (10 m)

1 CR2450 battery (included)

Approx. 28,000 triggers

SHC1000, SHC1000W

Door knocker casing:

2.3" x 3.8” x 1.1” ( 59 x 97 x 28 mm)

Motion sensor unit:

1.7" x 2” x 0.5” ( 44 x 52 x 14 mm)

Receiver unit:

1.5" x 1.1” x 0.2” ( 37 x 29 x 6 mm)

Door knocker casing:

1.3 oz ( 36 g)

Motion sensor unit:

0.7 oz ( 21 g) (without batteries)

Receiver unit:

0.2 oz ( 5.5 g)

Door knocker casing; Motion sensor unit

(inside knocker casing); Receiver unit;

Magnetic wall mount; Battery lock;

Screwdriver; 1 CR2450 battery.

Model

Detection Angle

IPX4

Splash-proof

Detection Distance

Transmission Distance

to Receiver

Power Source

Battery Life

32 ˚F ~ 113 ˚F (0˚C ~ 45˚C)

Operating

Temperature

Compatible Model

Size (WxHxD)

Weight

Package Contents

Transmission Distance:

32 ft (10m) between motion sensor unit and receiver

unit inside the camera. When you choose Portable

Mode, make sure the two units are within the transmis-

sion distance.

Sensor Detection Area:

Detection angle: 90 degrees (horizontal).

Detection distance: 13 ft (4 m) (centerline).

(approx. 5 ft (1.5 m) on both sides of the centerline).

One camera supports up to 6 motion sensors. You

make dierent channel combinations to identify each

unique motion sensor.

Motion Sensor Pairing Channel Switch:

Pairing Channel Combination:

1 2 3

Channel 1:

1 2 3

Channel 4:

1 2 3

Channel 5:

1 2 3

Channel 6:

1 2 3

Channel 2:

1 2 3

Channel 3:

3. Pair sensors.

Pin the pairing button

for 4~6 secs. (place the

motion sensor within

12 in (30cm)).

On motion sensor, LED

light ashes blue.

On receiver unit, LED light

ashes red.

On camera screen,

motion sensor icon

appears.

12 3

4 5 6

4~6 secs

32 ft

(10 m)

1. Motion Sensor takes around 30 secs to warm

up after sensor pairing is done.

2. Run motion sensor test and make sure the

camera is working properly.

www.brinno.com/support/registration

For manuals in other languages, visit

www.brinno.com/support

The product features, specications sheets and instructions may

dier from actual products. Please refer to Brinno ocial site for

the latest version of user manual.

1 2 3

Channel 1 (default):

Time

2013/05/01

17:30

Set

Exit

Press to Exit

Delete Sensor

Sensor 1

Delet all

Exit

Time

2013/05/01

17:30

Set

Exit

Press to Confirm

CONFIRM: Delete

Sensor 1?

Yes

Press to Setup

Paired Motion Sensor

Sensor 1

1. The screen displays all paired sensors.

2. Select one sensor or all sensors to be deleted from

the list.

3. Press SHUTTER BUTTON again to delete.

Press SHUTTER

BUTTON to go to

the DELETE SENSOR

option.

Press SHUTTER

BUTTON to conrm

deletion.

4. Restart the camera. The selected sensor will be

permanently deleted.

1. Insert receiver unit into camera.

2. Turn the camera power on.

BSMI 有電池產品

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

警告

本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理使用過之電池。

FCC

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT.

This equipment has been tested and found to comply with the limit s for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment o and on,

theuser is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

NCC LP0002

低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更

頻率、加大功率或變更原設計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應

改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻

電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts

de licence.L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage adioélectrique subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

RF Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator

& your body. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm

de distance entre la source de rayonnement et votre corps.

15.19 Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) this device may not cause harmful interference and

2) this device must accept any interference received, including interference that may cause undesired

operation of the device.

5 ft

(1.5 m)

5 ft

(1.5 m)

90°

13 ft

(4 m)

Brinno MAS200 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brinno MAS200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info