Bedienungsanleitung Brinno TLC 100 (Seite 7 von 16) (Englisch)

569540

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

To turn on the TimeLapse Camera

To turn o the TimeLapse Camera

• If the USB flash drive is full, or the batteries are completely empty, TimeLapse Camera will not turn on. If the

batteries are too low for normal operation, it will turn on and beep twice, the red LED will turn on, and then

TimeLapse Camera will beep six times and turn off. If the USB flash drive is full, or not installed, TimeLapse

Cam will turn on and beep twice, then after a few seconds the blue LED will turn on, then TimeLapse Camera

will beep six times and turn off.

• When TimeLapse Camera is in operation the green LED will turn on for about one second every 15 seconds to

indicate that the camera is running properly and is ready to take photos.

• If there is any other status to report, the camera will do so at the same time as the green LED flashes. If the

batteries are getting low the red LED will turn on in unison with the green LED. If the USB flash drive is getting

close to being full, then the blue LED will turn on in unison with the green LED.

• If the camera has previously automatically shut down due to low batteries or a full USB flash drive, the next

time the power button is pressed the red or blue LED will turn on and will stay on until the green LED turns on.

This allows you to determine the cause of the automatic shutdown so that the appropriate corrective action

can be taken.

• The green LED will also turn on and flicker for a few seconds while a picture is captured at the chosen time

setting, and then is stored on the USB flash drive. This indication of TimeLapse Camera activity is independent

of the status indication that occurs every 15 seconds.

NOTE

On the front of the TimeLapse Camera, above the lens, there are three LED lights.

These LEDs allow you to monitor the status of the camera without having to move the camera from its

mounted position.

Press and hold the orange power button on the front of the camera until the green LED lights up. After a few

seconds the TimeLapse Camera will beep twice to indicate it has properly initialized and is waiting to start

a time-lapse sequence. After a delay of approximately 5 seconds the TimeLapse Camera will take the rst

picture of the time-lapse sequence.

Press and hold the orange power button until the TimeLapse Camera beeps three times and the green

LED turns o. This may take several seconds because the TimeLapse Camera must rst power itself on

and initialize before it recognizes the turn o request. Please be patient and wait for the beeps and LED

indication.

Each LED supports a dierent function:

Green LED light: Power ON/OFF and status

Red LED light: Low battery level

Blue LED light: Low USB ash drive level

Beep:

Power ON: Two beeps

Power OFF: Three beeps

Error status: Six beeps

(error = no USB ash driver, USB memory short, low battery)

TimeLapse Camera Operation

5 -

Brinno TimeLapse Camera

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brinno TLC 100 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info