Bedienungsanleitung Brita 3-Way Water Filter Dispenser (Seite 10 von 13) (Englisch)

504591

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

ENGLISH 9

7 Technical data of the P 1000 cartridge

Operating pressure 2 bar to max. 8.6 bar

Water intake temperature 4°C to 30°C

Ambient tem-

perature for

operation 4°C to 40°C

storage/transport –20°C to 50°C

Nominal service ﬂ ow

(acc. to DIN 18879)

60 L/h

Capacity up to carbonate hardness

8.5 °dH at setting “+”

1000 L

Capacity from carbonate hardness

8.5 to 17 °dH at setting “++”

500 L

Pressure loss by nominal service ﬂ ow 0.2 bar

Empty ﬁ lter cartridge volume 1 L

Weight (dry/wet) 1.0 kg/1.4 kg

Dimensions

(Width/Depth/

Height)

Filter system

(ﬁ lter head with ﬁ lter

cartridge)

117 mm/108 mm/265 mm

Filter cartridge 108 mm/108 mm/259 mm

Installed dimensions

(vertical installation

with wall mounting

bracket)

137 mm/130 mm/265 mm

Operating position Horizontal and vertical

Water inlet connection G3/8"

Water outlet connection G3/8"

8 Troubleshooting

A No water ﬂ ow

Cause: Water intake closed.

Troubleshooting: Open the water intake at the upstream shut-off

valve or by closing the locking handle (3) on the

ﬁ lter head. Check hoses for kinks.

B No or low water ﬂ ow in spite of open water intake

Cause: Mains pressure too low.

Troubleshooting: Check mains pressure. If the fault continues,

check the ﬁ lter system and ﬁ lter cartridge and

replace if necessary. Check hoses for kinks.

Cause: Filter head not mounted in direction of water

ﬂ ow / hoses wrongly connected.

Troubleshooting: Dismantle ﬁ lter head and hoses and install in

direction of water ﬂ ow (chapter 3.4).

C Leak

Cause: Screwed connections not ﬁ tted correctly.

Troubleshooting: Check mains pressure. Check all screwed

connections and mount as described in

chapter 3.4.

D Incorrect display or incorrect settings on the electronic

cartridge exchange indicator with display

Cause: Buttons pressed in wrong order or wrong

buttons pressed.

Troubleshooting: Press and hold the RESET button for

8 seconds.

For models WD 3030 and WD 3040 only

These models have an aerator with two integrated outlets. The

Inner one is for BRITA ﬁ ltered water, the outer area for hot and cold

water. As with every tap aerator, there can be lime scale build up

in the outer area. Therefore it is recommended to clean the aerator

on a regular basis. For cleaning: Unscrew the cap on the end of the

dispensers neck. The aerator is connected to a silicon hose. Detach

it carefully and clean the aerator (e.g. with vinegar). After cleaning

connect the long, thin part on the back of the aerator carefully with

the silicon hose. Place the cap over the aerator and screw it tight.

Make sure that the gasket in the cap is seated correctly. When

installed correctly there should not be any leaks whilst running hot,

cold or BRITA ﬁ ltered water.

If you want to replace the aerator with a new one, you can order

it from BRITA. You can ﬁ nd the contact details for your BRITA

customer service team next to your country code on the back of

this booklet.

(ﬁ g. 10)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brita 3-Way Water Filter Dispenser Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info