Bedienungsanleitung Brita PURITY 600 Quell ST (Seite 23 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

504579

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

4 Installation

Caution: Prior to installation, read the Technical Data (Chapter 12) and the Operating and Safety

Information (Chapter 3). After the product has been stored and transported at temperatures below

0°C, it must be stored with the original packaging open for at least 24 hours before commissioning.

4.1 Delivery Scope

For installation of a PURITY Quell ST new ﬁ lter, you need the packaging units pressure vessel

(incl. ﬁ lter cartridge) and pressure vessel lid

Prior to installation, remove the entire delivery scope from the packaging and check that everything

is present:

1 x Pressure Vessel

1 x Pressure Vessel Lid

1 x Filter Cartridge

1 x Manual

1 x Carbonate Hardness Test

If part(s) of the delivery scope are missing, please contact your local BRITA Ofﬁ ce.

4.2 Assembling the Pressure Vessel and the Pressure Vessel Lid

Stand on the kick loops •

Lift the pressure vessel •

and turn clockwise until the mantle handles

are

over the kick loops

Remove the transport protective cap •

from the ﬁ lter cartridge.

Check the O-ring seal of the ﬁ lter cartridge •

for correct seat in the groove

and for dirt and damage.

Note:• The cartridge seat has been lubricated with food-safe lubricant at the

factory.

Stand on the kick loops •

Place the pressure vessel lid •

in the position “INSERT“ on the pressure

vessel

with the lock

in the appropriate groove.

Press the pressure vessel lid •

down and turn clockwise until the lock

engages.

Push the ﬂ ush hose •

onto the ﬂ ush valve

4.3 Assembly of Inlet and Outlet Hoses (e.g. coffee machine)

Note: The inlet and outlet hoses are not included in the standard scope of delivery. The use of

BRITA hose sets (Chapter 12) or hoses according to DVGW W543 is recommended. The ﬂ ush valve

supplied ensures that the hose to the consumer (e.g. coffee machine) is closed in the ﬂ ush posi-

tion.

Fit hoses to the inlet and outlet of the pressure vessel lid •

. Ensure that the O-rings on the

inlet and outlet are seated correctly.

Note: No additional use of ﬂ at seals is necessary.

Caution: The max. tightening torque at the 1" and 3/4" connections must not exceed

15 Nm! When using hoses not made by BRITA make sure that only connections with ﬂ at seals

are used. Conical seal shapes damage the ﬁ lter head connections and invalidate any guarantee

claims. The ﬂ ow direction indicated by the arrows on the connector head

must be observed.

During assembly, comply with the installation dimensions (Chapter 11), bending radii of the

hoses and dimensions of the accessories (e.g. hose sets). The system can be operated verti-

cally and horizontally. Use the wall mounting (Chapter 12) to install the system in a vertical posi-

tion only! If no original BRITA hose sets are used, the 1" – 3/4" reducer

supplied must be used

to ensures correct sealing of the non-return valve.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brita PURITY 600 Quell ST Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info