Bedienungsanleitung Brita PURITY C (Seite 19 von 74) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

504581

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

4.1 Assembling the Filter Head, Water Connection

Caution: Ensure that the locking handle on the head is open.

• Close water intake and switch off power supply to the terminal equipment.

• Fit the wall mounting bracket

in the intended position.

Caution: During assembly, note the installation dimensions, bending radii of the

hoses and dimensions of the accessories (e.g. BRITA FlowMeter). The system can be

operated vertically and horizontally. When using the wall mounting bracket, only install in

a vertical position!

• Fit the hoses to water inlet “IN”

and outlet “OUT”

of the ﬁ lter head

. With

G3/8" connections use ﬂ at seals and with John Guest connections use hoses with an

8 mm diameter. Both safety clips

need to be used with John Guest connections after

assembling the hose.

Caution: The max. tightening torque at the G3/8" connections must not exceed

14 Nm! Only hose connections with ﬂ at seals may be used because hoses with conical

screw connections may damage the ﬁ lter head connections, thereby invalidating any

guarantee claims! Only hoses that comply with DVGW-W 543 may be used for connec-

tion to the device. The use of BRITA hose sets (Chapter 10) is recommended.

• Check by-pass setting

and adjust to local carbonate hardness, if necessary

(Chapter 4.2).

Note: The by-pass has been factory set at 30%.

• Lock the ﬁ lter head

in the wall mounting bracket

4.2 Setting By-Pass and Capacity

• Identify the carbonate hardness of the local water using the BRITA carbonate hardness test

(Art. 710800). Alternatively, your local water supplier will provide information on carbonate

hardness.

Note: The water is not decarbonised when using PURITY C AC ﬁ lter cartridges; the carbonate

hardness does not need to be determined.

• Determine the by-pass setting and capacity according to the application and the carbonate hard-

ness identiﬁ ed using the by-pass and capacity table (Chapter 6).

• Then turn the by-pass setting

to the identiﬁ ed value.

Note: Only PURITY C 0–70% ﬁ lter heads have a variable by-pass setting. Installation of the

BRITA FlowMeter 10–100 A (Art. 298900) is recommended for the precise, continuous control

of the degree of ﬁ lter cartridge exhaustion.

Note: All the intake water is ﬁ ltered when using PURITY C AC ﬁ lter cartridges. The ﬁ lter car-

tridge can be used with both a variable and ﬁ xed by-pass. The by-pass used where required in

the ﬁ lter head is not taken into account.

4.3 Inserting the ﬁ lter cartridge

• Remove protective cap

• Note the next exchange date in the date ﬁ eld on the ﬁ lter cartridge

• Insert the ﬁ lter cartridge

vertically in the ﬁ lter head

Caution: The ﬁ lter cartridge can only be inserted when the locking handle is open.

Make sure that the ﬁ lter cartridge is positioned correctly.

• Turn the locking handle

until you feel it engage.

4.4 Commissioning

• Open the water intake and switch on the terminal equipment’s power supply.

• Operate the ﬂ ush valve

and ﬂ ush the ﬁ lter system until the ﬁ ltered water runs clear

and without bubbles. At least two empty ﬁ lter cartridge volumes must be ﬂ ushed

( Chapter 9).

Note: When bleeding/ﬂ ushing, catch water emerging from the ﬂ ush hose

in an

appropriate container.

• Check system for any leaks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brita PURITY C Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info