Bedienungsanleitung Brita PURITY Quell ST (Seite 27 von 166) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

504582

Zoom out

Zoom in

Vorherige Seite

1/166

Nächste Seite

• A non-return valve according to DIN EN 13959 tested by the DVGW has been factory installed

at the water intake of the ﬁ lter head.

• No copper pipes and no galvanised or nickel-plated pipes/connectors may be installed between

the water ﬁ lter and the consumer. The use of BRITA hose sets is recommended here. When

choosing the material for parts that come into contact with water after the BRITA ﬁ lter system

it must be remembered that, due to the process, decarbonised water contains free carbon diox-

ide.

• All parts must be installed in accordance with the country-speciﬁ c guidelines on the installation

of drinking water facilities.

• For erection and operation of the ﬁ lter system, the BG rules “Working in Kitchens“ of the Spe-

cialist Committee “Foods“ of the BGZ (BGR111) must be observed.

4 Installation

Caution: Prior to installation, read the Technical Data (Chapter 12) and the Operating and Safety

Information (Chapter 3). After the product has been stored and transported at temperatures below

0°C, it must be stored with the original packaging open for at least 24 hours before commissioning.

4.1 Delivery Scope

For installation of a PURITY Quell ST new ﬁ lter, you need the packaging units pressure vessel

(incl. ﬁ lter cartridge) and pressure vessel lid

Prior to installation, remove the entire delivery scope from the packaging and check that everything

is present:

1 x Pressure Vessel

1 x Pressure Vessel Lid

1 x Filter Cartridge

1 x Manual

1 x Carbonate Hardness Test

If part(s) of the delivery scope are missing, please contact your local BRITA Ofﬁ ce.

4.2 Assembling the Pressure Vessel and the Pressure Vessel Lid

• Stand with both feet on the kick loops

• Lift the pressure vessel

and turn it clockwise until the mantle handles

are over the kick loops

• Remove the transport protective cap

from the ﬁ lter cartridge.

• Check that the O-ring seal of the ﬁ lter cartridge

is correctly seated in the

groove and also check for dirt and damage.

Note: lubricant at the factory.

• Stand on the kick loops

with both feet and place the pressure vessel lid

on the pressure vessel

. The position of the arrow marking on the lid

handle

must match the “INSERT” groove.

• Press the pressure vessel lid

down and turn clockwise until the lock

engages.

4.3 Assembly of Inlet and Outlet Hoses

Note: The inlet and outlet hoses are not included in the standard scope of delivery. The use of

BRITA hose sets is recommended (Chapter 13).

• Fit inlet hose

at the inlet of the connector head

and outlet hose

at the outlet of the con-

nector head

Note: Inlet “IN” and outlet “OUT” of the connector head

are equipped with O-rings as

seals, therefore no additional ﬂ at seals may be used here. Check that the O-rings are seated

correctly.

Caution: The max. tightening torque at the 1" and 3/4" connections must not exceed 15 Nm!

Only hose connections with ﬂ at seals may be used. Hoses with conical screwed connections dam-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brita PURITY Quell ST Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info