772958

Britax-Romer ADVANSAFIX Z-LINE Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
09
1
2
30 32
26
20
32 26
45
20 21
1
2
21
44
08
22
20
19 19
45
2
1
44
1
2
32
30
26
20
19
07
26
19
08 21 32
20
1. GENERAL SAFETY INSTRUCTIONS 2. USE IN THE VEHICLE 3. APPROVAL 4. CARE AND MAINTENANCE
6. Release the two press studs on the seat cover and fold the cover forwards.
Whendoing so, pull the SecureGuard 26 out of the cover.
7. Loosen the 5-point harness 09 on the child seat as far as possible.
Tip: Pull the two shoulder straps forward while pressing the adjustment button 18 .
8. Release the two opened shoulder cushions 19 from the Velcro strip and fold them
around the shoulder straps 08 .
DANGER Make sure that the shoulder straps 08 pass correctly through theshoul-
der cushions 19 .
9. Remove the belt clips 21 from the recess provided on the 44 inside of the backrest.
10. Raise the grey release plate 32 and push it along with the SecureGuard 26 towards
the backrest 30 .
11. Turn the grey release plate 32 around so that the harness buckle 20 is at the top
and the SecureGuard 26 is at the bottom.
12. Store the SecureGuard 26 in the recess provided and push the grey release plate
32 back into its holder until it engages with an audible click.
13. Pass the harness buckle 20 through the slot in the cover which is nearer
tothebackrest.
We recommend using the 5-point harness as long as possible and making the conver-
sion only when your child starts to weigh more than 15 kg and has reached the highest
position of the headrest.
1. Loosen the 5-point harness on the child seat as far as possible 09 .
2. Open the harness buckle 20 and place the belt clips 21 in the belt guides
onthesides.
3. Loosen the press studs on the backrest and fold the upper half of the cover up-
wards and the lower half downwards.
4. Insert the belt clips 21 in the recess provided on the 44 inside of the backrest.
5. Open the two shoulder cushions 19 by the Velcro fasteners on the side.
6. Push the Velcro strip of the two opened shoulder cushions 19 under the back-
restcover and attach it to the fleece strip provided.
Check that the two shoulder cushions are not overlapping.
7. Pull the adjusting strap 22 to tighten the harness.
8. Release the two press studs on the seat cover and fold the cover forwards.
Whiledoing this, pull the harness buckle 20 out of the cover.
9. Raise the grey release plate 32 and push it along with the harness buckle 20
towards the backrest 30 .
10. Turn the grey release plate around 32 so that the SecureGuard (B) 26 is at the top
and the harness buckle (A) 20 is at the bottom.
11. Stow the harness buckle 20 in the recess provided and push the grey release plate
32 back into the holder until it engages with an audible click.
12. Pass the SecureGuard 26 through the slot in the cover with sow-on B (15-36 kg).
13. Close the two bottom press studs on the cover.
14. Close the two top press studs on the cover.
15. Close the two press studs on the upper cover of the headrest.
11. REMOVING THE 5-POINT HARNESS AND RE-ATTACHING SECUREGUARD
12. RE-ATTACHING THE 5-POINT HARNESS AND REMOVING SECUREGUARD
9 to 36 kg
9 m. ~ 12 y.
GB
User instructions
Child seat back
1. Slide the headrest 07 to the lowest position.
2. Press the safety catch at the centre of the group change switch 45 , at the same
time moving it to the lower position for use with Group 1 (9-18 kg).
Child seat front
3. Fold the lower part of the headrest cover upwards and lay it over the headrest.
4. Open the two press studs on the inside of the headrest cover.
5. Release the two press studs on the back of the cover.
Please refer to your vehicle’s instruction manual for instructions on how to use child
restraint systems. This seat can be used in vehicles with ISOFIX & Top Tether anchorage
points, in vehicles with ISOFIX & 3-point harness (see type list) and in vehicles with 3-point
harness.
Please refer to your vehicle’s instruction manual for information on the seats approved
aschild seats for weight class 9 to 36 kg.
The ADVANSAFIX Z-LINE is approved for three dierent installation methods:
a) This means that the child seat may only be used in vehicles listed on the enclosed vehicle type list.
This type list is constantly being updated.
The latest version can be obtained from us or from our website at www.britax-roemer.com
You can install your child seat as follows:
Facing forwards
(in the direction of travel)
Yes
Facing backwards
(against the direction of travel)
No 1)
With 2-point harness No
With 3-point harness2) Yes
with ISOFIX fixing points
(between seat surface and backrest)
Yes
On front passenger seat Yes 3)
On outer rear seat Yes
On centre rear seat
(with 3-point harness) Yes 4)
1) Installation is permitted on backward-facing car seats (e.g. in a van or minibus) only if these seats are
also approved for carrying adults. The seat must not be within the activated range of an airbag.
2) The safety belt must be approved to ECE R 16 (or a comparable standard), which is indicated on the
harness test label by an "E" or "e" inside a circle.
3) If there is a front airbag: Slide the car seat well back and follow the relevant instructions in the vehicle’s
instruction manual.
4) It cannot be used if there is only a 2-point belt available.
Group Installation method Approval type Section
of user
instructions
1 (9-18 kg) ISOFIX + Top Tether universal A
2/3 (15-36 kg) ISOFIT + car seat belt semi-universala) B1
2/3 (15-36 kg) Car seat belt universal B2
BRITAX RÖMER
Child seat
Testing and certification
In accordance with ECE* R 44/04
Group Body weight
ADVANSAFIX Z-LINE
I+II+III 9 to 36 kg
*ECE = European Standard for Child Safety Equipment
The child seat has been designed, tested and approved according to the require-
ments of the European Standard for Child Safety Equipment (ECE R 44/04).
The E certification mark (in a circle) and approval number can be found
on the orange approval label (sticker on the child seat).
DANGER! The certification is invalidated if you make any modifications to the
child seat. Only the manufacturer is permitted to make modifications to the child seat.
The child seat is approved for use both with and without the XP-PAD.
DANGER! Never secure your child or the child seat with a 2-point belt. If you
secure your child in the child seat with a 2-point belt only, this may cause serious
injuries to your child in the event of an accident and could even cause death.
WARNING! The
ADVANSAFIX Z-LINE
must be used exclusively for securing
your child in the vehicle. It is in no way suitable for use as a seat or toy in the home.
Please take the time to read these instructions carefully and always keep
them in the storage pouch provided
14 on the child seat for later reference.
The instructions must accompany the child seat if it is later passed on to athird
party.
DANGER! For the protection of your child:
• Before closing the vehicle door, check that neither your child nor any parts
of the child seat can get jammed in the door.
• In the event of an accident at a collision velocity greater than 10 km/h, it is pos-
sible that the child seat may be damaged without the damage being immediately
visible. In this case the child seat must be replaced. Please dispose of it properly.
• Always have the child seat examined if it has been damaged (e.g. if it falls to the
ground).
• Regularly check all important parts for damage. In particular, ensure that
all the mechanical parts are fully functional.
• Never lubricate any parts of the child seat with grease or oil.
•
Never leave your child unattended in the child seat in the vehicle.
• Have your child enter and exit the vehicle on the pavement side only.
• When not in use, protect the child seat from direct exposure to sunlight.
The child seat can become very hot in direct sunshine. Children's skin is sensi-
tive and could be harmed as a result.
•
The more snugly the belt ts over your child's body, the safer your child will be. There-
fore, avoid having your child wear thick clothes under the belt.
• On long journeys, take regular breaks in order to give your child a chance to run
about and play.
• If using on the rear seat: Move the front seat far enough forward to ensure that
your child's feet will not knock against the backrest of the front seat (to prevent
the risk of injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or accident, unsecured objects or people may
cause injury to other occupants in the vehicle. Therefore, please always ensure
that ...
• no load-bearing contact points are used other than those specied in these
instructions and those marked on the child seat.
• the backrests of the car seats are secured (for example, check that any fold-
down rear seat bench has snapped into place).
• all heavy or sharp-edged objects present in the vehicle (e.g. on the parcel shelf)
are held securely.
• all persons in the vehicle have their seatbelts fastened.
• the child seat is secured whenever it is in the vehicle, even if it is not carrying
a child.
WARNING! For your protection when handling the child seat:
• Never use the child seat in a free-standing position, not even for testing.
•
To avoid damage, ensure that the child seat is not jammed in between hard ob-
jects (car door, seat rails, etc.).
•
Keep the child seat in a safe place when not in use. Do not place heavy objects
on the seat and do not store directly next to heat sources or in direct sunlight.
CAUTION! To protect your vehicle:
• Certain car seat covers made from more sensitive materials (e.g. velour, leather,
etc.) may show wear marks after a child seat has been used. For optimum
protection of your car seat covers, we recommend using the BRITAX RÖMER
car seat protector from our range of accessories.
Child seat back
16. Press the safety catch at the centre of the group change switch 45 , at the same
time moving it to the upper position for use with Group 2/3 (15-36 kg).
14. Close the two bottom press studs on the cover.
15. Close the two top press studs on the cover.
16. Close the two press studs on the upper cover of the headrest.
TAKING CARE OF THE HARNESS BUCKLE
To ensure the safety of your child, it is essential that the harness buckle continues
tofunction correctly. Harness buckle malfunctions are usually caused by dirt accumu-
lation or by external objects. Such malfunctions may be:
• When you press the red release button, the buckle clips are ejected only slowly.
• The buckle clips no longer engage (i.e. they pop out again when you try to push
them in).
• The buckle clips do not engage without an audible click.
• The buckle clips are dicult to push in (you feel a certain amount of resistance).
• It takes a lot of force to open the harness buckle.
Remedy
Rinse out the harness buckle so that it works perfectly again:
CLEANING THE HARNESS BUCKLE
1. Open the Velcro fastener on the crotch cushion 31 and remove it.
2. Remove the grey release plate 32 as described in Section “11. REMOVING
THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.
3. Place the release plate 32 along with the harness buckle 20 in warm water
withsome washing-up liquid for at lease one hour.
4. Thoroughly rinse the harness buckle 20 and dry it completely.
5. Attach the grey release plate 32 as described in Section 11. “ REMOVING
THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.
6. Attach the crotch cushion 31 .
CLEANING
CAUTION Please ensure that you use only original BRITAX replacement seat cov-
ers, as the seat cover is an integral part of the child seat and is important for correct
functioning of the system. Replacement seat covers are available from your dealer.
CAUTION! The child seat must not be used without its cover.
• The seat cover can be removed and washed with a mild detergent in a washing
machine with the “Delicates” programme (30 °C). Please follow the instructions
onthe washing label of the seat cover.
• The shoulder cushions can be removed and washed in lukewarm soapy water.
• The plastic parts, SecureGuard, XP-PAD and the belts can be cleaned with soapy
water. Do not use aggressive cleaning agents (such as solvents).
Removing the shoulder cushions
1. Loosen the shoulder straps 08 as far as possible.
2. Open the shoulder cushions 19 by the Velcro fasteners at the side.
Child seat back
3. Bring the top tether 13 forward over the front of the seat.
4. Unhook the storage pouch 14 at the top.
5. Pull out the shoulder straps 08 a little so that you can see the rubber loops
oftheshoulder cushions 19 underneath.
6. Unhook the rubber loops from the plastic bars 41 on the shoulder strap height
adjuster 42 .
7. Pull the shoulder cushions 19 forwards out of the harness slots.
Reattaching the shoulder cushions
Simply follow the steps above in reverse order.
CAUTION The shoulder cushions 19 and belts must not be twisted or swapped
over. The shoulder straps 08 must be located under the black cover band 43
inthe shoulder cushions 19 .
08
19 14
13
41
42
08
43
Removing the cover
Headrest
1. Open the two press studs 33 at the belt slots.
2. Push the headrest of the child seat to the topmost position.
3. Pull the elastic band up from the edge of the tray and pull the tabs 34 out
ofthetwo slots in the seat pan.
4. Pull the cover edge out of the gap between the seat pan and the inlay cushion.
5. Unhook the rubber loops 35 under the headrest.
Seat pan
6. Undo the Velcro fastener on the crotch cushion 31 and remove it.
7. Open the four press studs 36 on the seat and back surface.
8. Push the harness buckle 20 or SecureGuard 26 through the cover slot.
9. Unhook the rubber loops 37 at the front under the seat surface and pull the tabs
38 out of the seat pan.
10. Pull the rubber loops carefully out of the gap around the belt guides 28 .
11. Pull the cover edge and tabs 39 out of the gap between the seat pan
andtheinlay cushion.
12. Pull the rubber loops 40 at the top of the back of the backrest out of the gap
inthe seat pan and and unhook them.
Reattaching the cover:
Simply follow the steps above in reverse order.
33
34
35
31
20
36 37
38
28 40
39
CAUTION! If the child seat is installed with Method A, always install the harness
buckle 20 correctly, and if installed with Method B, always install SecureGuard 26
correctly. Make sure that the release plate 45 is correctly attached.
CAUTION! Check that the straps are not twisted and are laid correctly through
the slots in the cover. The rear slot in the seat cover is provided for the harness buck-
le 20 and the front slot is provided for the SecureGuard 26 . The slot at the front edge
of the seat is for the harness adjusting strap 22 .
2000033724 - 11/19
www.britax-roemer.com
ADVANSAFIX Z-LINE
Please observe the waste disposal regulations in your country.
Disposal of packaging Container for cardboard boxes
Seat cover Residual waste, waste incineration
Plastic parts To be placed in the corresponding container
according to the labels
Metal parts Container for metals
Belt straps Container for polyester
Buckle and clip Residual waste
10. DISPOSAL
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Britax-Romer ADVANSAFIX Z-LINE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Britax-Romer ADVANSAFIX Z-LINE

Britax-Romer ADVANSAFIX Z-LINE Bedienungsanleitung - Deutsch - 2 seiten

Britax-Romer ADVANSAFIX Z-LINE Bedienungsanleitung - Holländisch - 2 seiten

Britax-Romer ADVANSAFIX Z-LINE Bedienungsanleitung - Französisch - 2 seiten

Britax-Romer ADVANSAFIX Z-LINE Bedienungsanleitung - Spanisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info