Bedienungsanleitung Britax-Romer KIDFIX 2 R (Seite 1 von 2) (Englisch)

767964

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

BRITAX RÖMER

Kindersicherheit GmbH

Theodor-Heuss-Straße 9

89340 Leipheim

Germany

+49 (0) 8221 3670 199

BRITAX Excelsior Limited

1 Churchill Way West

Andover

Hampshire SP10 3UW

United Kingdom

+44 (0) 1264 386034

BRITAX Nordiska Barn AB

Jörgen Kocksgatan 4

SE-211 20 Malmö

Sweden

www.britax-roemer.com | hello@britax-roemer.com

BRITAX RÖMER Child Safety EMEA

15 – 36 kg

10 22

06 07

03 16

www.britax-roemer.com

2000031236 19/12

User instructions

KIDFIX² R

KIDFIX² S

15 kg – 36 kg

(~4 Y – 12 Y)

1. SAFETY NOTES 2. INTRODUCTION

5. ADJUSTING THE HEADREST

7. DISASSEMBLY AND DISPOSAL

4. USE IN THE VEHICLE 6. CARE AND MAINTENANCE

3. APPROVAL

If you have any further questions about the use of the child seat, please

Please take the time to read these instructions carefully and keep

them to hand in the storage compartment provided on the child safe-

ty seat at all times! The instructions must accompany the child seat if

it is passed on to athird party!

DANGER! To protect your child:

• In the event of an accident at acollision speed of more than 10 km/h, the

child seat may be damaged without the damage being immediately visi-

ble. In this case the child seat must be replaced. Please dispose of it

properly.

• Always have your child seat checked if it has been damaged (e.g by fall-

ing to the ground).

• Regularly check all important parts for damage. In particular, ensure that

all the mechanical parts are fully functional.

• Never apply oil or grease to any parts of the child seat.

• Never leave your child unattended on the child seat in the vehicle.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Protect the child seat from intense direct sunlight when not in use. The

child seat can become very hot in direct sunshine. Children's skin is sen-

sitive and could be harmed as aresult.

• The more snugly the belt ﬁts over your child's body, the better the

child will be protected. Therefore, avoid having your child wear thick

clothes under the belt.

• On long journeys, take regular breaks in order to give your child the

chance to run about and play.

DANGER! For the safety of all vehicle occupants:

In the case of an emergency stop or accident, unsecured objects or people

may cause injury to other occupants in the vehicle. Therefore, please always

ensure that ...

• the backrests of the vehicle seats are locked (e.g. If there is afolding rear

seat bench, check that it is latched in place).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf)

are secured.

• all persons in the vehicle have their seat belts fastened.

• the child seat is secured whenever it is in the vehicle, even if not carrying

achild.

WARNING! For your protection when handling the child seat:

• Never use the child safety seat in afree-standing position, even for testing.

• When swivelling the backrest up, 12 nothing must come between the

back-rest 12 and the seat cushion 09 . You or your child’s ﬁngers could be

jammed and injured.

• To avoid damage, ensure that the child seat is not jammed in between

hard objects (car door, seat rails, etc.).

• Keep the child seat in asafe place when not in use. Do not place heavy

objects on the seat and do not store it directly next to sources of heat or

in direct sunlight.

CAUTION! To protect your vehicle:

• Certain car seat covers made from more sensitive materials (e.g. velour,

leather, etc.) may show signs of wear when achild seat is used on them.

For optimum protection of your car seat covers, we recommend using the

BRITAX RÖMER car seat protector from our range of accessories.

We are delighted that you have chosen our child seat to accompany your

child safely through anew stage in his or her life.

To protect your child correctly, the child seat must always be used and

installed as described in these instructions!

These instructions use the following symbols:

Symbol Keyword Explanation

DANGER! Risk of serious physical injury

WARNING! Risk of minor physical injury

CAUTION! Risk of material damage

TIP! Useful notes

Instructions that follow aﬁxed sequence are numbered.

Example:

1. Press the button...

Belt guide colours

For clear dierentiation, the two vehi-

cle seat belts are shown in dierent

colours. The diagonal strap 16 is

shown in dark red and the lap belt 15

in bright red. The belt guides on the

child safety seat follow the same col-

our scheme.

BRITAX RÖMER

Child seat

Testing and certiﬁcation

In accordance with ECE* R 44/04

Group Body weight

KIDFIX² R

KIDFIX² S II+III 15 to 36 kg

*ECE = European Standard for Child Safety Equipment

This child seat has been designed, tested and approved according to the re-

quirements of the European Standard for Child Safety Equipment (ECE R

44/04). The certiﬁcation mark (letter E in acircle) and approval number can

be found on the orange approval label (sticker on the child seat).

DANGER! The certiﬁcation is invalidated if any modiﬁcations are made to

the child seat. Only the manufacturer is permitted to make modiﬁcations

to the child safety seat. The child seat is approved for use both with and

without SecureGuard.

WARNING! The KIDFIX² R and KIDFIX² S must be used exclusively for

securing your child in the vehicle. They are in no way suitable for use as

aseat or atoy in the home.

DANGER! Never secure your child or the child seat with a2-point belt. If

your child is secured in the child seat with a2-point belt only, this may

cause serious injuries, which could even be fatal.

Please refer to your vehicle’s instruction manual for instructions on

how to use child restraint systems. The seat can be used in vehicles with

ISOFIX anchoring systems (see type list) and in vehicles with 3-point

belts.

Please refer to your vehicle’s instruction manual for information on the

seats approved as child seats for weight class 15 to 36 kg.

The KIDFIX² R and KIDFIX² S are approved for two dierent installation

methods:

Symbol Installation type Approval type

with the ISOFIT locking arms in the ISOFIX ﬁxing

points on the vehicle. Check the list of vehicle

types.

semi-universal a)

with the vehicle's 3-point seat belt universal

a) This means that the child seat may be used only in vehicles that are listed in the at-

tached vehicle type list. This type list is constantly being updated. The latest version

can be obtained from us or at www.britax-roemer.com

You can install your child seat as follows:

in the direction of travel Yes

against the direction of travel No1)

with 2-point belt No

with 3-point belt 2) Yes

with ISOFIX ﬁxing points

(between seat surface and

backrest)

Yes

On front passenger seat Yes

On outer rear seat Yes

on centre rear seat

(with 3-point belt) Yes

1) Use is permitted on arear-facing vehicle seat (e.g. in avan or minibus) only if the vehi-

cle seat is also approved for use by adults. The seat must not be within the activated

range of an airbag.

2) The safety belt must be approved to ECE R 16 or acomparable standard (indicated on

the belt’s test label by an "E" or "e" inside acircle).

3) If there is afront airbag: Slide the car seat well back and follow the related instructions

in the vehicle’s instruction manual.

4) Cannot be used if the vehicle seat is equipped with a2-point belt only.

1. Grasp the adjustment handle 10 on the back of the

headrest 22 and pull it upwards. This unlocks the

headrest.

2. You can now move the unlocked headrest 22 to

the desired height. When you release the adjust-

ment handle 10 , the headrest 22 locks into place.

3. Place the child seat on the car seat.

4. Sit your child on the child seat and check the height.

Repeat the above procedure until the headrest 22 is

at the correct height.

A correctly adjusted headrest 22 ensures optimal positioning of the diago-

nal strap 16 , and gives your child optimum protection. The headrest 22

must be positioned so that two ﬁngers can be inserted between your

child's shoulders the headrest 22 .

To adjust the height of the headrest to ﬁt your child:

Please ensure that you only use original BRITAX RÖMER replacement seat

covers, as the seat cover is an integral part of the child safety seat and fulﬁls

important functions that ensure smooth operation of the system. Replace-

ment seat covers are available from your dealer.

• The cover can be removed and washed with amild detergent, selecting

the “Delicates” programme on the washing machine (30 °C). Please ob-

serve the instructions on the washing label of the cover.

• The plastic parts can be cleaned in soapy water. Do not use aggressive

cleaning agents (such as solvents).

DANGER! The child safety seat must not be used without the seat cover.

Removing the seat cover

1. Push the headrest of the vehicle seat to its top posi-

tion.

2. Unhook the cover hook 19 on the rear of the back-

rest.

3. Pull o the top part of the cover and fold it forwards

onto the seat surface.

4. Release the cover hooks 19 on the front of the back-

rest and on both sides of the seat surface and loosen

the plastic cards on the front of the seat cushion.

5. Pull the cover away from the seat surface.

Removing the headrest cover

1. Unhook the cover straps 20 on the rear of the back-

rest.

2. Unhook the cover hooks 19 on the front of the back-

rest.

3. Pull the headrest cover 22 o; to do this, detach the

two hooks on the bottom of the headrest.

►The cover can now be washed. Please observe the

instructions on the washing label of the cover.

Putting the cover on

Follow the above steps in the reverse order to put the cover

on.

UNFASTENING YOUR CHILD:

To unfasten your child, press the release button on the car seat buckle.

DANGER! The child seat must always be secured when in the vehicle, even

if not carrying achild.

RE-ATTACHING THE BACKREST:

4. Follow steps 1 - 7 in paragraph 10.1 “Removing the backrest“ in the re-

verse order.

Please follow the disposal regulations applying in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, thermal recycling

Plastic parts To be placed in the corresponding container

as labelled

Metal parts Container for metals

Belt straps Container for polyester

Buckle and clip Residual waste

1. Press the release button on car vehicle seat buckle.

2. Open the dark red belt holder 03 by pressing the

button on the belt holder 03 backwards, then pull out

the diagonal

belt 16 .

Only for installation type A (ISOFIT):

3. To release the ISOFIT ﬁtting, squeeze the green lock-

ing button 07 and red release button 06 together, ﬁrst

on one side then on the other.

►The child safety seat can now be removed.

REMOVAL:

Remove the seat cover

1. Fold up the cover of the backrest

2. Fold the cover of the seat shell

forwards.

Remove the seat cover

1. Fold up the cover of the backrest

2. Fold the cover of the seat shell

forwards.

Remove SecureGuard

8.1

Installing SecureGuard

8.2

Remove SecureGuard

1. Press the SecureGuard

downward and slide the Se-

cureGuard

out of the recess

TIP! Keep the SecureGuard

for later use.

Attaching SecureGuard

1. Take the SecureGuard

and position it right in front of

the recess

2. Slide and press the metal plate

into the recess

until the plate

clicks into place.

We recommend using the seat with SecureGuard.

TIP!

The following chapters describe use with

SecureGuard.

3. Unhook the cover straps on the seat shell

4. Pull the SecureGuard

downward and away through the

seat cover.

5. Remove the plastic cards

of the seat cover from the seat

shell

6. Remove the cover and the seat cushion.

Mounting the seat cover

1. Position the seat cover on the seat shell

2. Insert the plastic cards

of the seat cover into the

designated recesses on the seat shell

3. Pull the seat cover over the seat shell

4. Hook the cover straps back onto the seat shell

5. Position the seat cover behind the backrest cover

3. Unhook the cover straps on the seat shell

4. Remove the plastic cards

of the seat cover from the

seat shell

5. Remove the cover and the seat cushion.

Mounting the seat cover

1. Position the seat cover on the seat shell

2. Pull the SecureGuard

through the slot in the seat

cushion.

3. Insert the plastic cards

of the seat cover into the desig-

nated recesses on the seat shell

4. Pull the seat cover over the seat shell

5. Hook the cover straps back onto the seat shell

6. Position the seat cover behind the backrest cover

8. Remove and install SecureGuard

Britax-Romer KIDFIX 2 R Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Britax-Romer KIDFIX 2 R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info