Bedienungsanleitung Britax-Romer MAX-WAY (Seite 31 von 33) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

536074

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

IMPORTANT – The child seat can be used with either a lap or a lap and

diagonal seat belt.

The larger the child the more upright the seat must be. To change the position

(if required) slide the support leg out until it engages in the desired position.

To slide the support leg in push the two support leg adjuster buttons and pull

up the support leg (dia 3a). Make sure the support leg is engaged rmly.

Place the child seat rearward facing with the back of the child seat positioned

centrally between the driver and passenger seat.

Extend the footprop fully by pressing the two release Buttons.Make sure

that the footprop tether brackets are facing forwards and that the straps

are not twisted. Lower the footprop and adjust the height so that it is within

approximately 30mm of the oor (dia 3b). Use the ruler printed on the back

page of this manual to get the correct distance from the footprop to the oor.

Loop a tether strap around both the

front driver and passenger seat as

shown (dia 3c).

If your car is equipped with a runner

loop on the seat runners, these may be

used as an alternative (see detail 3d).

IMPORTANT – Do not install the tether

straps using the Luggage loops

3. Installing your child seat (rearward facing) in rear middle seat

Slide the loop ends of the tether straps between the front car seat and back

as shown (dia 2d &

dia 2e). Bring the hook ends of the tether straps

round the outside of the car seat and feed through the loops

. Snap

the hooks of the tether straps onto the xing rings on the back of the child

seat

. Provisionally tighten the tether straps by pulling the loose ends

downwards

Open the other lock-off arm , feed the seat belt under the lock-off arm and

attach the tongue into the buckle (dia 3g).

Pull all of the seat belt slack through

the child seat ensuring the seat belt

is not twisted (dia 3h). When the belt

is as tight as possible, close the lock-

off arms on BOTH sides of the seat

ensuring that they click into place.

If the buckle now lies in the position

marked as wrong with a

and the

seat belt cannot be correctly tightened

(dia 3i), try another seating position in

the car.

Pull off sufcient lap and diagonal belt (approx.600 – 900mm). Open the lock-

off arm on the side opposite the seat belt buckle. Pull back the child seat cover

to reveal the crotch strap. Feed the belt through the lock-off belt guide and seat

shell slot (dia 3f) on to the top face of the seat base, behind the crotch strap

(inset) and down through the slot on the other side of the child seat.

Finally tighten the tether straps by pulling the loose ends downwards (dia 3j)

until the footprop touches the oor. The footprop must rest on a solid oor –

not on lids of storage boxes or similar.

Once rmly strapped in, test the child seat by trying to move it back and forth

and side to side. If it seems loose, you must reinstall until rmly installed.

DO NOT rest the back of the child seat against the driver or front passenger

seats.

9-25 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Britax-Romer MAX-WAY Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Britax-Romer MAX-WAY

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info