Bedienungsanleitung Brixton BQ-6311 (Seite 24 von 50) (Deutsch, Englisch, Holländisch, Französisch)

531007

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

GAS CONNECTION

Check whether your barbecue is installed correctly. This manual provides detailed mounting

instructions which include specific mounting procedures. Strictly observe these instructions to ensure

correct and safe installation of the barbecue.

For correct functioning of the barbecue, it is important to place the barbecue on an even surface.

This barbecue is set up to be used with butane or propane gas bottles from 5kg till 15kg, with

appropiate gas pressure regulator.

For replacement of the gas pressure regulator and hose please see below table for correct

specifications:

Category

Gas and pressure

Countries

Injector

I3+ (28-30/37)

Butane 28mbar /

Propane 37mbar

GB. IE, BE. CH. ES. FR.

GR. IT & PT

Burner: 0,97mm

Side burner: 0,90mm

I3 B/P (30)

Butane / Propane

30mbar

DK, FI, GR, LU, NL, NO

& SE

Burner: 0,97mm

Side burner: 0,90mm

The gas hose must not be longer than 1.5 mtr. Only use approved connections. The gas hose

needs to be adjusted if national circumstances require. The gas hose needs to be fitted in such

a way that it can not be twisted.

For your safety:

Make sure all black plastic grommets of the pressure regulator are in place, and that the hose is not

making contact with the heat protection of the BBQ itself.

Connect the pressure regulator to your gas cylinder.

VERY IMPORTANT:

 The temperature of the regulator may not exceed 60°C (140F).

The regulator must be equipped with a safety valve or pressure limiter.

 The opening of the regulator must fit the connection of the gas tap of the cylinder.

 Check whether the gas tap of the tank is completely closed (turn clockwise until the knob stops).

 Check whether the gas tap of the gas cylinder is provided with suitable outer threads.

 Make sure that all burner knobs are set to position “off”.

 Remove the protective cover from the gas tap of the gas cylinder. Always use the protective cover

supplied with the gas tap.

 Inspect the connection between the gas tap and the pressure regulator. Look for damage and dirt.

Remove any debris. Check the hose for any damage. Never try using damaged or blocked

equipment. Contact your local L.P. gas supplier for repairs.

 When connecting the pressure regulator to the gas tap, manually turn the nut clockwise until it

doesn’tgo any further. Do not use a wrench to tighten the nut. Using a wrench can damage the

joints, which can be dangerous (as illustrated in the picture below).

 Turn the gas tap of the cylinder fully open (counter-clockwise). Use a solution of water and soap to

check for any leakage before trying to ignite the grill. If you encounter a leak, you must shut off the

gas tap and only use the grill after the leak is repaired by a local L.P. gas supplier.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brixton BQ-6311 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info