Bedienungsanleitung BRK DVRAD1610 (Seite 13 von 56) (Englisch)

606732

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Page 13

Power On/Off

To power the system On/Off, connect the power cable to the DC 12V port on the rear panel. Press the toggle

switch to the on position in the back of the DVR. At startup, the system performs a basic system check

and runs an initial loading sequence. After a few moments, the system loads a live display view.

User Login

Password

ATTENTION: By default, passwords are disabled on the system. You

do not need to enter a password when accessing any system menus.

However, for security purposes, it is highly recommended to enable

passwords on the system using the Password Menu. See “Password”

section for details on setting up passwords. Right click and

select Login. No password is required when no password is

set up. Right click again to show the quick access menu

Quick Access Menu

When using the mouse, use the Quick Access Menu to

access several system options, including the System

Setup Menu. Select one of the following options:

• System Setup: Opens the main system menu

• View Layout: Provides a choice of viewing channels on the

monitor

• View 1: Allows viewing of 1 channel

• PIP: Allows viewing of 2 channels,

Picture in Picture

• View 4: Allows viewing of 4 channels

• View 8: Allows viewing of channels 1

through 8, with channel 1 in large view mode

• Split 9: Allows viewing of

channels in a 3 x 3 channel grid

• Split 16: Allows viewing of

channels in a 4 x 4 channel grid

• Video Adjust: Adjust video image settings by channel

• PTZ: Opens the PTZ control menu

• Clients: Network user status

• Snapshot: Allows you to take a photo of the

channel that the cursor is on, and save to HDD

• Photos: Review save Snapshots, and upload to USB drive

• Record Setup: Access to recording settings

for each channel, begin manual recording

• Playback: Open the Search Menu

and playback recorded video

• Clear Alarm: Cancel alarms

• Shutdown: Allows a choice of logging out,

powering down or restarting the DVR system

INITIAL SETUP

SYSTEM OPERATION

Main Viewing Screen

User Login Menu

Power Switch

NOTE: Powering down stops the system. The power LED is still on. The only way to fully power down

the system is by turning the power off & on with the power switch on the back of the DVR.

System Start Up

Powering your DVR and Cameras

The power supply included with the DVR is rated for 5 amps. Normally, this is enough to power both the

DVR and supplied cameras. However, using aftermarket cameras or a larger number of cameras may sur-

pass the capability of the power supply, causing the systerm to shut down. Most devices should be marked

with the Amperage rating, but some may be marked by wattage. In this case, Amp usage can be found by

dividing Watts by Volts, or A=W/V. The power supply should be upgraded if it surpasses 80% of its rating

(i.e., 4 amps for a 5 amp power supply), to compensate for momentary spikes in current draw. Note: One Amp equals 1000 milliamps

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BRK DVRAD1610 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info