Bedienungsanleitung BRK HS-4705-400 (Seite 14 von 29) (Englisch)

606847

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Page 26 Page 27

advanced operatIon

PTZ

remote access

network setup

netWork setup - remote access

Use the NETWORK SETUP menu to conﬁgure your network and DNS settings for remote access. If you are only going to access

the DVR locally from a computer attached to the same router as the DVR, you only

need to conﬁgure settings using either the DHCP or STATIC IP. Because you are on

the same network, port forwarding and knowing the public IP address are not

necessary. You will just access the DVR by entering the IP address of the DVR from

the NETWORK setup into the Internet Explorer browser window. If you are going to

take advantage of the Remote Surveillance feature, such as for a smart phone or to

view your system outside of your network over the internet you will need to review

and set up Port Forwarding and the DDNS. After you setup the NETWORK settings

using DHCP , STATIC IP or DDNS, see the REMOTE SURVEILLANCE section for

further instructions.

There are ﬁve options for conﬁguring the DVR to be accessed remotely: DHCP,

Static IP, UPnP, PPPOE, and DDNS. To access this menu, from the MAIN MENU

click ADVANCED then NETWORK SETUP. Be sure your router or network is con-

nected to the LAN port on the back of the DVR.

DHCP (Dynamic Host Conﬁguration Protocol)

DHCP is a protocol used by networked devices (clients) to obtain various parameters necessary for the clients to operate in an

Internet Protocol (IP) network. It allows you to quickly connect to your network and obtain an IP address from the router. After

the initial setup, we recommend that you disable DHCP, then select STATIC from the TYPE drop down box and set the IP address

between 1~100. For example, if your IP address is 192.168.0.107, change the last digits to 90 (i.e. 192.163.0.90). This ensures that

port forwarding will not change in the event of power failure or resetting of your network.

To conﬁgure DHCP settings:

1. Select DHCP from the TYPE drop down box in the NETWORK SETUP Menu. You should see the message “Getting IP...”

The router will assign an IP address. This is the IP address you will forward port 80 to on the router so you can access the

DVR from remote computers See comment above to conﬁgure a static IP.

2. Click APPLY. Click OK in the conﬁrmation window.

3. If necessary, change the Media and Web Port settings

Static IP

You will need to setup the network settings on the DVR to match the settings of the router to which your DVR is connected. This

information can be obtained through your computer. Windows 7, Vista or XP all have similar ways to access this data.

To get the router settings:

1. To access the router’s settings you will need to enter the Command (CMD) panel on your computer. It must be connected

to the same router as your DVR.

• In Windows 7 or Vista, from the “START” menu type “CMD” in the ﬁeld that says, “Search programs and ﬁles” and hit

ENTER or click on the magnifying glass icon.

• In Windows XP select “Run” from the “START” menu. Type “CMD” after the prompt

2. Type “ipconﬁg” at the prompt and hit enter

3. You will get a screen that contains information similar to what is shown below. Within all of the information shown,

locate the IPv4, Subnet Mask and Gateway addresses. These you will enter into the STATIC IP screen in the NETWORK

SETTINGS menu in your DVR. See next step.

Network Setup

Windows “ipconﬁg” Info Example

Pan/Tilt/Zoom (PTZ) Setup Continued:

In the PTZ Senior Control screen you can set or control the following for each PRESET deﬁned:

1. SET PRESET: Saves any PRESET functions changed with this screen.

2. CLEAN PRESET: Clears a deﬁned PRESET without going to the SET CRUISE screen.

3. CALL PRESET: Calls a deﬁned PRESET without going to the SET CRUISE screen.

4. AUTO SCAN: Enables AUTO SCAN feature without going through Quick Access Menu.

5. STOP SCAN: Enables AUTO SCAN feature without going through Quick Access Menu.

6. CRUISE SETTING: Conﬁgures the Cruise Setting. See next step for details.

Step 4: Conﬁgure the CRUISE SETTING of your PTZ Camera.

This feature allows you to set up a series of Pan, Tilt and Hold camera sequences and then

execute those operations in a continuous loop. This is useful when you want to record or

view the same set of pre-determined areas. You can customize these settings for each PTZ

camera connected to your DVR.

Understanding the CRUISE SETTING Options:

To access this menu In Live View, double click on the Channel with the connected PTZ

Camera to open to full screen view. From the Quick Access Menu select PTZ. Click SETUP

from the PTZ SETUP screen and you will see the PTZ SENIOR CONTROL Menu. Click SET

CRUISE to conﬁgure the cruise settings for your PTZ Camera.

1. TOTAL: The total number of PRESET’s deﬁned

2. PRESET: A deﬁned pan, tilt and hold sequence. You can enter up to 128 PRESET’s for a

channel depending on how many areas you want to view or record.

3. STOP TIME: The total time in seconds for the camera to move through its deﬁned

operation. Note: This includes travel time from the previous set point completion plus the length of time you want the camera

to hold on a position. For example, if the STOP TIME is set to 10 seconds and the travel time from the previous set point is

6 seconds, then the camera will hold on the position for only 4 seconds. It can take some trial and error to get the timing you

want. To help ﬁne tune your timing after a set point is deﬁned, selecting CALL will travel through the complete cruise setting

for the PRESET allowing you to adjust your timing.

4. SET: Stores the PRESET in memory

5. CLEAR: Removes the deﬁned pan, tilt and hold sequence for a PRESET.

6. APPLY: Saves all PRESETS deﬁned.

How to deﬁne a Cruise Setting PRESET

1. With your PTZ Channel selected and the CRUISE SETTING menu open as explained in the previous sections, be sure TOTAL

is 0 and you are on PRESET 001. If not click CLEAR to reset the PRESET’s.

2. Using the Arrow Keys adjust the camera to the ﬁrst position you want to monitor.

3. Set the STOP TIME setting using the Virtual Keypad. (See STOP TIME explanation above for important information)

4. Click SET to save. The TOTAL and PRESET numbers move to the next number.

5. Repeat steps 2 through 4 for each PRESET you want to deﬁne.

6. Click APPLY to save all PRESETS for this CRUISE SETTING.

7. Follow the same steps above to conﬁgure other PTZ cameras on other Channels.

8. Click EXIT several times to get to the Live View screen

9. Use the Quick Access Menu to select START CRUISE and STOP CRUISE to begin or end Cruise operation for all deﬁned PTZ

channels.

PTZ Setup - Sub Menu

PTZ Setup

PTZ Cruise Setting

BRK HS-4705-400 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info