Bedienungsanleitung BRK PRO-D1610 (Seite 22 von 48) (Englisch)

606724

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Page 22

ADVANCED Operation

ALARM

Hard Drive and USB Options continued:

Formatting the USB Flash Drive

Use a USB ﬂash drive to backup recorded video and upgrade the system`s ﬁrmware. You should always format the USB ﬂash

drive you intend to use with the system.

NOTE: Not formatting the USB ﬂash drive may result in improper functionality.

Advanced Setup

Use the DEVICE MANAGEMENT menu to conﬁgure alarm settings, motion

detection, mobile surveillance, PTZ settings and the hard drive. The Device

Management menu contains the following sub-menus: HDD, Alarm, Mobile,

Motion Detect, and PTZ.

Alarm

Alarm and E-mail Options:

Use the ALARM SETUP menu to conﬁgure alarm and e-mail settings. NOTE:

External alarm devices must be connected to the alarm block on the rear panel

of the DVR in order to use the I/O (input/ output) alarms of the system. Up to

four external alarm devices can be connected to this DVR. Devices 1 and 2 work

with channels 1-8. Devices 3 and 4 work with channels 9-16. See next section

“Alarm Inputs” and “Alarm Inputs Diagram” for details on attaching alarm inputs.

To access this menu, from the MAIN MENU click ALARM.

To conﬁgure alarm settings:

1. Under I/O STATUS, select NO (Normal Open), NC (Normal Closed), or OFF

for Alarm input. Next under I/O RELATION select SETUP and choose

what channel or channels you want to link to this alarm device in the I/O

RELATED CHANNEL screen. Click APPLY to save your settings. Repeat

if desired for the remaining I/O devices. Note: If in the RECORD screen a

Channel is set to OFF, ALARM is also disabled for that Channel.

2. To activate Loss Alarms use the drop down menu and select ON/OFF:

• HDD LOSS: The alarm will sound if the internal HDD is damaged

• HDD SPACE: The alarm will sound when the HDD is full (overwrite must

be disabled)

• VIDEO LOSS: The alarm will sound when a camera is disconnected

3. Under ALARM MANAGE, conﬁgure the following:

• OUTPUT: Set the output time (in seconds) on the spot monitor from 0s,

10s, 20s, 40s, or 60s, 5MIN, 10MIN.

• BUZZER: Set the time (in seconds) for the DVR buzzer to sound when an

alarm is triggered—0s, 10s, 20s, 40s, or 60s, 5MIN, 10MIN. NOTE: Set the

buzzer to 0s if you want to disable the alarm during motion detection.

• POST REC: Set the time (in seconds) for the system to record after a

triggered alarm—30s,

1MIN, 2MIN, 5MIN

Device Management

USB Flash Drives

The system is compatible with most major brands of USB ﬂash drives, with capacities from 256 MB to 4 GB. If

you need to reformat your ﬂash drive then click on the U DISK FORMAT button while the USB drive is connected

to the USB port on the front of the DVR. Be aware that this button is not for use with any external USB hard drive

you may connect to the DVR for backup. External hard drives will need to be formatted using the FAT32 format

and this can be done by connecting the drive to the USB port on a PC and reformatting it from there.

Alarm Setup Menu

Alarm Manage Screen

Alarm Setup I/O Related Channel Screens

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BRK PRO-D1610 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info