Bedienungsanleitung BroilKing Baron S490 (Seite 5 von 36) (Englisch, Französisch, Spanisch)

637969

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

All factory-made connections have been rigorously tested

for gas leaks. However, shipping and handling may have

loosened a gas fitting.

AS A SAFETY PRECAUTION:

• Test all ﬁ ttings for leaks before using your gas grill.

• Test the cylinder valve for leaks each time the cylinder

is ﬁ lled.

• Test for leaks every time you connect a gas ﬁ tting.

• Do not smoke at any time while testing.

• Never test for leaks with a lit match or open ﬂ ame.

• Test for leaks outdoors.

TO TEST FOR LEAKS:

1. Extinguish any open flame

or cigarettes in the area.

2. Be sure that cylinder valve and

gas grill valves are “OFF.”

3. Connect LP gas cylinder. See “Hose and Regulator.”

4. Prepare a soap solution of one part water, one part liquid

detergent.

5. With a full gas cylinder, open cylinder slowly.

6. Brush the soap solution on each connection.

7. A leak is identified by a flow of bubbles from the area of

the leak.

8. If a leak is detected, close the gas cylinder “shut-off” valve,

tighten the connection and retest.

9. If the leak persists, contact your gas grill dealer for

assistance. Do not attempt to operate appliance if a leak

is present.

If your gas grill is equipped with a side burner or rear

burner:

1. Follow steps 1 - 5 above

2. Place fingertip over the opening in the orifice at the end

of hose.

3. Turn “SIDE”/”REAR” control to “HIGH.”

4. Brush soap solution on each connection between orifice

and control valve.

5. Turn “SIDE”/”REAR” control to “OFF”.

Always keep venturi tubes clean. Blockages in the venturi

tubes caused by spiders, insects and nests can cause a

flashback fire. In fact, although the gas grill may still light, the

backed up gas can ignite and cause a fire around the venturi

tubes at the control panel or the side burner.

VENTURI TUBE SPIDER WEB TUBE BURNER

If a ﬂ ashback ﬁ re occurs, turn off gas at the source

immediately

Inspect and clean the venturi tubes (main burner, side

burner, rear burner) if any of the following symptoms

occur:

1. You smell gas.

2. Your gas grill does not reach temperature.

3. Your gas grill heats unevenly.

4. The burners make popping noises.

INSPECTING & CLEANING VENTURI

TUBES

1. Turn off gas by closing the propane cylinder valve

2. When gas grill is cool, remove the burner fasteners and

the top portion of the collector box. Proceed to lift the

burners from the gas grill housing.

3. Clean the venturi tubes with a pipe cleaner or venturi

cleaning tool (Accessory #77310 or #18270).

4. Lower the burner into position in the gas grill housing,

making sure that the venturi tubes are correctly aligned

and fitted on the orifices.

5. Secure burners with burner fasteners.

6. Snap top portion of collector box back in place.

LEAK TESTING VENTURI TUBES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BroilKing Baron S490 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BroilKing Baron S490

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info