Bedienungsanleitung Brother BE-1204B-BC - PC control (Seite 244 von 262) (Englisch)

644489

244

Zoom out

Zoom in

Vorherige Seite

1/262

Nächste Seite

11-4 BE-1204B-BC • BE-1206B-BC

Chapter 11 Error code list

Code Error Measures

E-36 Needle overhang (-X, +Y)

E-38 Needle overhang (-Y)

E-39 Needle overhang (+X, -Y)

E-3C Needle overhang (-X, -Y)

Pattern or the needle position is out of the embroidering area.

Reset the embroidering area on the panel or move the hoop to

the sewable position.

E-40

The status of presser foot is issued as an alarm

when every second machine is used.

E-41 Invalid start-up error

This is not usually displayed.

E-42 XY movement error

Press the

or turn on the F/B switch on the head to either

side. If this error occurs frequently, check if the tension of the

pulley belt is proper.

E-43 I/F CPU failed to read EEPROM data

Turn the power off and on once. If the same error occurs

again, the main PC is faulty.

E-44

Failed in the communication with inter-head

CPU

Press the

or turn ON the F/B switch on the head to either

side. If the same error occurs again, the connector of

communication cable on the inter-head CPU may be

disconnected.

E-45 Failed in the communication with head CPU

Press the

or turn ON the F/B switch on the head to either

side. If the same error occurs again, the connector of

communication cable on the head CPU may be disconnected.

E-46 Failed in the communication with XY CPU

Press the

or turn ON the F/B switch on the head to either

side. If the same error occurs again, the main PCB is faulty.

E-47 Failed in the communication with I/F CPU

Press the

or turn ON the F/B switch on the head to either

side. If the same error occurs again, the main PCB is faulty.

E-48 The main shaft rotated the opposite way

Turn OFF the power and check if the sensors of the encoder A

and B are connected correctly, not mixed-up each other. If

those connections are correct, then check if the pin connections

of the main shaft motor connectors are correct.

E-49 Can not identify the machine model

Turn OFF the power, check if the model identification harness is

connected properly, and turn ON the power again.

E-4A Failed in the communication with I/O CPU

Press the

or turn ON the F/B switch on the head to either

side. If the same error occurs again, the connector of

communication cable on the I/O PCB may be disconnected.

E-A1 Spindle motor lock

Press the

or turn on the F/B switch on the head to either

side. If it occurs frequently, the main shaft mechanism is

faulty.

E-A2 Main PC board temperature too high

E-A3 Spindle motor voltage too low

E-A4 Spindle motor voltage too high

E-A5 Spindle motor CPU error

E-A6

Spindle motor CPU communication command

error

E-A7 Spindle motor CPU send/receive error

This is not usually displayed.

E-A8 Spindle stop position signal error

Adjust the pulley stop position (100 °) above the needle and

press the

. If the error occurs frequently, the parts related

to the main shaft stop position sensor are faulty.

E-A9 Spindle CPU parameter error

E-B0 Lower shaft CPU error

E-B1 Thread tangle in rotary hook

This is not displayed in this model.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother BE-1204B-BC - PC control Seite 244

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info