Bedienungsanleitung Brother Brother Innov-is XJ1 (Seite 29 von 212) (Englisch)

718772

Zoom out

Zoom in

Vorherige Seite

1/212

Nächste Seite

LCD SCREEN

Getting Ready

Using the Machine Settings Key

Press to change the default machine settings

(needle stop position, embroidery speed, opening

display, etc.). To display the different settings screens,

press for “Sewing settings”, for “General

settings”, for “Embroidery settings” or for

“Wireless LAN settings”.

■ Sewing Settings

1 Select whether to use the sewing speed controller to

determine the zigzag width (page 79).

2 Make adjustments to character or decorative stitch

patterns (page 97).

3 Adjust the presser foot height. Select the height of the

presser foot when the presser foot is raised.

4 Adjust the presser foot pressure. The higher the number,

the greater the pressure will be. Set the pressure at [3]

for normal sewing.

5 Adjust the amount of fabric feeding of the dual feed foot

(page 53).

6 Select whether [1-01 Straight stitch (Left)] or [1-03

Straight stitch (Middle)] is the utility stitch that is

automatically selected when the machine is turned on.

7 Select whether utility stitches or quilting stitches

are displayed first on the stitch selection screen.

8 You can activate this setting after connecting the multi-

function foot controller (sold separately). (These settings

appear when the multi-function foot controller is

connected to the machine.)

9 Select the height of the presser foot when sewing is

stopped when the pivot setting is selected (page 65).

0 Select the height of the presser foot when the machine is

set to free motion sewing mode (page 80).

A When set to [ON], the thickness of the fabric is

automatically detected by an internal sensor while

sewing. (page 67)

B When set to [ON], reinforcement stitches are sewn at the

beginning and/or end of sewing for a reinforcement

stitch pattern, even when (Reverse stitch button) is

pressed (page 60).

C Adjust the guideline marker position and brightness

(page 65).

D Select whether to lower the presser foot automatically

before starting sewing. (page 61)

E Select whether to raise the presser foot automatically

when stopping sewing. (page 61)

F Select whether pressing (Thread cutter button)

automatically lowers the presser foot before cutting the

thread. The presser foot will be raised after the thread is

cut. (page 61)

G You can save the current settings screen image in a USB

media by pressing this button when the USB media is

inserted into the USB port. The files are saved in a folder

labeled [bPocket].

H Reset settings on this page to original default. Some

settings are not reset.

Memo

• Press or to display a different settings

screen.

Controller Functions that can be specified

Main foot controller Start/Stop

Heel switch Select any of the following:

• [Thread Cutting]

• [Needle Position Up/Down]

• [Single Stitch]

• [Reverse Stitch] (Reinforcement

Stitch)

• [Presser Foot Up/Down]

• [No setting]

Side pedal

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Brother Innov-is XJ1 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Brother Innov-is XJ1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info