Bedienungsanleitung Brother DCP-340CW (Seite 35 von 43) (Englisch)

120853

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

Installing the Driver & Software

Macintosh

Wireless

Network

Macintosh

2 Turn on the machine by plugging in the power

cord.

Improper Setup

If you have previously configured the wireless

settings of the machine you must reset the

network (LAN) settings before you can

configure the wireless settings again.

Press Menu.

Press a or b for 3.LAN and press Set.

Press a or b for 0.Factory Reset and press

Set.

Press a for Reset.

If the machine asks you Reboot OK?, press a

for Yes. The machine will restart automatically.

3 On your machine, press Menu, then use the a,

b and Set keys to choose 3, 6, then WLAN,

then a Yes to reboot the machine. The wired

network interface will become inactive with this

setting.

It will take about a minute for the LAN menu on

the LCD to become available again.

A four level indicator on the right of your

machine’s LCD shows the wireless signal

strength.

4 When the LAN menu becomes available, press

Menu, then use the a, b and Set keys to

choose 3, 3, 1. This will start the wireless setup

wizard.

5 The machine will search for your network and

display a list of available SSIDs. You should

see the SSID you wrote down earlier. If the

machine finds more than one network use the

a or b keys to choose your network, then

press Set.

6 Use the a, b and Set keys to choose one of

the options below: If your network is configured

for Authentication and Encryption you must

match the settings used for your network.

No Authentication or Encryption: Choose

Open system, press Set then choose None

for Encryption Type and press Set. Then

press a Yes to apply your settings. Go to step

No Authentication with WEP Encryption:

Choose Open system, press Set then use the

a or b to choose WEP for the Encryption

Type and press Set. Go to step 7.

Authentication with WEP Encryption:

Choose Shared Key, press Set. Go to step 7.

Authentication with WPA-PSK (TKIP)

Encryption: Choose WPA-PSK, press Set. Go

to step 8.

7 Choose the appropriate key number and press

Set. Enter the WEP key you wrote down in step

1 using the a, b and Set keys to choose each

letter or number. You can use the

Enlarge/Reduce and Number of Copies keys

to move the cursor left and right. For example,

to enter the letter a, press the a key once. To

enter the number 3, hold down the a key until

it appears.

The letters appear in this order: lower case,

upper case, numbers and then special letters.

Press Set when you have entered all the

characters, then press a Yes to apply your

settings. Go to step 9.

Most access points and routers can store

more than one key, but they will only use

one at any time for authentication and

encryption.

8 Enter the WPA-PSK (TKIP) key WPA you wrote

down in step 1 using the a, b and Set keys to

choose each letter or number. You can use the

Enlarge/Reduce and Number of Copies keys

to move the cursor. For example, to enter the

letter a, press the a key once. To enter the

number 3, hold down the a key until it appears.

Press Set when you have entered all the

characters, then press a Yes to apply your

settings. Go to step 9.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother DCP-340CW Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother DCP-340CW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info