Bedienungsanleitung Brother DCP-365CN (Seite 24 von 38) (Englisch)

451171

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

For Wireless Network Users

Connecting the Brother machine to the wireless network

Configure the wireless

settings (typical Wireless

Setup in infrastructure

mode)

a On your machine, press Menu.

Press a or b to choose 3.Network and press

OK.

Press a or b to choose 2.WLAN and press OK.

Press a or b to choose 2.Setup Wizard and

press OK.

When Change to WLAN? is displayed, press

a to accept.

This will start the wireless setup wizard.

To cancel, press Stop/Exit.

b The machine will search for available SSIDs. If

a list of SSIDs is displayed, use the a or b keys

to choose the SSID you wrote down in

step 11-a on page 23, then press OK. If you

are using an authentication and encryption

method that requires a password, go to c.

If your authentication method is Open System

and your encryption mode is None, go to d.

If your access point is set to not broadcast the

SSID you will have to manually add the SSID

name. For details, see the Network User’s

Guide on the CD-ROM.

c Enter the Password you wrote down in

step 11-a on page 23 using the a, b keys to

choose each letter or number.

Use Enlarge/Reduce key or Number of

Copies key to move the cursor left or right.

For example, to enter the letter a, press the a

key once. To enter the number 3, hold down

the a key until it appears.

The letters appear in this order: lower case,

upper case, numbers and then special letters.

(For more information, see Entering Text for

Wireless Settings

(DCP-373CW/375CW/377CW only)

on page 37.)

Press OK when you have entered all the

characters, then press a Yes to apply your

settings. Go to d.

d Your machine will now try to connect to your

wireless network using the information you

have entered. If successful, Connected will

appear for 60 seconds on the LCD.

It may take a few minutes to connect to your

wireless network.

e Press OK.

Wireless setup is now complete.

To install MFL-Pro Suite, continue to

step 13.

For Windows

Users:

Now go to

Page 27

For Macintosh Users:

Now go to

Page 31

Note

It will take several seconds to display a list of

available SSIDs.

If a list of SSIDs is not displayed, make sure your

access point is on. Move your machine closer to

the access point and try starting from a again.

Note

If the LCD displays Wrong Password, the

password you entered did not match with your

access point. Verify your network settings

collected in step 11-a on page 23, then repeat a

to c to make sure you have entered the correct

information.

If the LCD displays Connection Fail, make

sure your access point is on, and verify your

network settings collected in step 11-a on

page 23. Temporarily move your machine as

close as possible to the access point, then

repeat a to c to make sure you have entered the

correct information.

If your access point does not have DHCP enabled

you will need to manually configure the IP

address, subnet mask and gateway of the

machine to suit your network. See Chapter 6 of

the Network User’s Guide for details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother DCP-365CN Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother DCP-365CN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info