Bedienungsanleitung Brother DCP-750CW (Seite 41 von 51) (Englisch)

451186

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

Installing the Driver & Software

Macintosh

Wireless

Network

Using the Setup Wizard from the control panel LAN menu for wireless

network configuration

Important

Make sure that you have finished the

instructions from Step 1 Setting Up the

Machine on page 4 through 11.

1 Write down the wireless network settings of

your access point or wireless router.

SSID (Service Set ID or Network name)

_________________________

WEP Key (if needed)

________________________

WPA/WPA2-PSK (TKIP or AES) (if needed)

_________________________

The WEP key is for 64 bit encrypted networks

or 128 bit encrypted networks and can contain

both numbers and letters. If you do not know

this information you should see the

documentation provided with your access point

or wireless router. This key is a 64-bit or 128-bit

value that must be entered in an ASCII or

HEXADECIMAL format.

For example:

WPA/WPA2-PSK enables a Wi-Fi

Protected

Access Pre-shared key (WPA/WPA2-PSK),

which lets the Brother wireless machine

associate with access points using TKIP or

AES encryption (WPA-Personal). WPA/WPA2-

PSK (TKIP or AES) uses a Pre-Shared Key

(PSK) that is more than 7 and less than 64

characters in length.

See the Network User’s Guide for more details.

Note

Make sure that the machine is turned on by

connecting the power cord.

Improper Setup

If you have previously configured the wireless

settings of the machine you must reset the

network (LAN) settings before you can

configure the wireless settings again.

On your machine, press Menu.

Press a or b for LAN and press OK.

Press a or b to choose Factory Reset, and

then press OK.

Press to choose Yes.

2 On your machine, press Menu.

Press a or b to choose LAN and press OK.

Press a or b to choose Network I/F and

press OK.

Press a or b to choose WLAN and press OK.

The wired network interface will become

inactive with this setting.

It will take about a minute for the LAN menu on

the LCD to become available again.

Press Stop/Exit.

3 When the LAN menu becomes available, press

Menu.

Press a or b to choose LAN and press OK.

Press a or b to choose Setup WLAN and

press OK.

Press a or b to choose Setup Wizard and

press OK.

This will start the wireless setup wizard.

4 The machine will search for available SSIDs. If

a list of SSIDs is displayed, use the a or b

keys to choose the SSID you wrote down in

step 1, then press OK. Go to step 8.

Note

It will take a few seconds to display a list of

available SSIDs.

If your access point is set to not broadcast the

SSID you will have to manually add the SSID

name. Go to step 5.

5 Select <NEW SSID> using a or b and press

OK. Go to step 6.

64 bit ASCII:

Uses 5 text characters.

e.g. “Hello” (this is case sensitive)

64 bit

Hexadecimal:

Uses 10 digits of hexadecimal data.

e.g. “71f2234aba”

128 bit ASCII:

Uses 13 text characters.

e.g. “Wirelesscomms” (this is case

sensitive)

128 bit

Hexadecimal:

Uses 26 digits of hexadecimal data.

e.g. “71f2234ab56cd709e5412aa3ba”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother DCP-750CW Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother DCP-750CW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info