Bedienungsanleitung Brother FS-60 (Seite 97 von 100) (Englisch)

631196

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

——

—————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

ERROR MESSAGES

If an operation is performed incorrectly before the sewing machine is set up, an error message appears on the

operation panel. Follow the instructions indicated in the table.

If you press the stitch selection key or do the operation correctly while the error message is displayed, the

message disappears.

Note

● If error message “F1” through “F9” appears in the LCD while the sewing machine is being used, the

machine may be malfunctioning. Contact your nearest authorized service center.

Operation beep (for models equipped with the operation beep)

Each time a key is pressed you will hear one beep. If a non-functioning key is pressed or an incorrect operation

is performed you will hear two or four beeps (only for models equipped with the operation beep).

■ If a key is pressed (correct operation)

One beep sounds.

■ If an incorrect operation is performed or a non-functioning key is pressed

Two or four beeps sound.

■ If the machine locks up, for example, because the thread is tangled

The sewing machine beeps for four seconds and the machine automatically stops. Be sure to check for the

cause of the error, and correct it before continuing to sew.

Error Message Probable Cause Solution

The foot controller was pressed (or the start/

stop button was pressed if the foot controller

is not connected) and the reverse/

reinforcement stitch button was pressed while

the presser foot is raised.

Lower the presser foot lever before

continuing the operation.

A stitch other than the buttonhole or bar tack

stitch was selected and the foot controller

was pressed (or the start/stop button was

pressed if the foot controller is not connected)

while the buttonhole lever is lowered.

Raise the buttonhole lever before

continuing the operation.

The buttonhole or bar tack stitch was selected

and the foot controller was pressed (or the

start/stop button was pressed if the foot

controller is not connected) while the

buttonhole lever is raised.

Lower the buttonhole lever before

continuing the operation.

The reverse/reinforcement stitch button or

needle position button was pressed while the

bobbin winder shaft is moved to the right.

Move the bobbin winder shaft to the

left before continuing the operation.

The start/stop button was pressed while the

foot controller was connected.

Disconnect the foot controller, and

then press the start/stop button.

Otherwise, operate the machine by

using the foot controller.

The motor locked up because the thread is

tangled.

Clean the race to remove the tangled

thread (p.82). After cleaning the race,

insert the bobbin case properly. If the

needle is bent or broken, replace the

needle. Then, thread the upper thread

properly, and continue the operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother FS-60 Seite 97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother FS-60

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info