Bedienungsanleitung Brother HL-5270DN (Seite 137 von 152) (Englisch)

1883

137

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

A. Appendix

129

 When FIM (US-Post Net) is selected with the parameter ‘t3’ or ‘T3’

Characters ‘A’ to ‘D’ are valid and one digit of data can be printed. Upper-case and lower-case alphabet

characters can be accepted.

 When Post Net (US-Post Net) is selected with the parameter ‘t4’ or ‘T4’

Numbers ‘0’ to ‘9' can be data and it must end with a check digit. ‘?’ can be used instead of the check digit.

 When EAN 8, EAN 13, or UPC A is selected with the parameter ‘t5’ or ‘T5’

Ten numbers ‘0’ to ‘9’ can be accepted as bar code data. The number of characters for bar codes is limited

as follows:

EAN 8: Total 8 digits (7 digits + 1 check digit)

EAN 13: Total 13 digits (12 digits + 1 check digit)

UPC A: Total 12 digits (11 digits + 1 check digit)

A number of characters other than those stated above will cause a data error that results in the bar code

data being printed as normal print data. If the check digit is not correct, the printer decides the correct

check digit automatically so that the correct bar code data will be printed. When EAN13 is selected, adding

‘+’ and a two-digit or five-digit number after the data can create an add-on code.

 When UPC-E is selected with the parameter ‘t6’ or ‘T6’:

The numbers ‘0’ to ‘9’ can be accepted as bar code data.

‘?’ can be used instead of a check digit.

Adding ‘+’ and two-digit or five-digit number after the data creates an add-on code.

 When Codebar is chosen with the parameter ‘t9’ or ‘T9’

Characters ‘0’ to ‘9’, ‘-’, ‘ . ’, ‘$’, ‘/’, ‘+’, ‘ : ’ can be printed. Characters ‘A’ to ‘D’ can be printed as a start-

stop code, which can be upper case or lower case. If there is no start-stop code, errors will happen. A

check digit cannot be added and using ‘?’ causes errors.

 When Code 128 Set A, Set B, or Set C is selected with the parameter ‘t12’ or ‘T12’, ‘t13’ or ‘T13’, or ‘t14’

or ‘T14’

Code 128 sets A, B and C can be individually selected. Set A shows characters Hex 00 to 5F. Set B

includes characters Hex 20 to 7F. Set C includes the pairs 00 to 99. Switching is allowed between the code

sets by sending %A, %B, or %C. FNC 1, 2, 3, and 4 are produced with %1, %2, %3, and %4. The SHIFT

code, %S, allows temporary switching (for one character only) from set A to set B and vice versa. The ‘%’

character can be encoded by sending it twice.

 When ISBN (EAN) is selected with the parameter ‘t130’ or ‘T130’

The same rules apply as for ‘t5’ or ‘T5’.

 When ISBN (UPC-E) is selected with the parameter ‘t131’ or ‘T131’:

The same rules apply as for ‘t6’ or ‘T6’.

Eight digits

1 2

(standard format) The first character must be ‘0’ and the data must end with a check digit.

Total eight digits =

‘0’ plus 6 digits plus 1 check digit.

Six digits

The first character and the last check digit are removed from the eight digit data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother HL-5270DN Seite 137

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother HL-5270DN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info