Bedienungsanleitung Brother Innov-is 4000 (Seite 227 von 249) (Englisch)

463623

227

Zoom out

Zoom in

Vorherige Seite

1/249

Nächste Seite

TROUBLESHOOTING

216

Needle breaks Needle is installed incorrectly. Reinstall the needle correctly. 34

Needle clamp screw is not tightened. Tighten the needle clamp screw. 35

Needle is turned or bent. Replace the needle. 34

Using improper needle or thread for the

selected fabric.

Check the “Fabric/Thread/Needle

Combination” chart.

Wrong presser foot was used. Use the recommended presser foot. “STITCH SETTING

CHART”

Upper thread tension is too strong. Adjust the thread tension setting. 43, 154

Fabric is pulled during sewing. Do not pull the fabric during sewing. —

Spool cap is set incorrectly. Check the method for attaching the spool cap,

then reattach the spool cap.

There are scratches around the holes in the

needle plate.

Replace the needle plate, or consult your

authorized dealer.

There are scratches around the hole(s) in the

presser foot.

Replace the presser foot, or consult your

authorized dealer.

There are scratches on the race. Replace the race, or consult your authorized

dealer.

210

Needle is defective. Replace the needle. 34

Fabric does not feed

through the machine

Feed dogs are set in the down position. Use the feed dog position lever to raise the

feed dogs.

Stitches are too close together. Lengthen the stitch length setting. 42

Wrong presser foot was used. Use the correct presser foot. “STITCH SETTING

CHART”

Needle is turned, bent or the point is dull. Replace the needle. 34

Thread is entangled. Cut the entangled thread and remove it from

the race.

—

Machine does not

operate

There is no pattern selected. Select a pattern. 48, 98, 130, 177

“Start/Stop” button was not pushed. Press the “Start/Stop” button. 3

Main power switch is not turned on. Turn the main power to ON. 8

Presser foot is not lowered. Lower the presser foot. 3

“Start/Stop” button was pushed with the foot

controller attached.

Remove the foot controller, or use the foot

controller to operate the machine.

Speed control lever is set to control the zigzag

stitch width.

Use the foot controller instead of the “Start/

Stop” button to operate the machine.

All keys and buttons have been locked by

Press to unlock all keys and

buttons.

32, 34

Embroidery unit does

not operate

There is no pattern selected. Select a pattern. 130, 177

Main power switch is not turned on. Turn the main power to ON. 8

Embroidery unit is not attached correctly. Reattach the embroidery unit correctly. 128

Embroidery frame was attached before the unit

was initialized.

Perform the initialization process correctly. 128

LCD display is difficult

to see

LCD contrast is not properly adjusted. Adjust the LCD contrast. 15, 212

Nothing happens,

even if the LCD

display is pressed

The screen has been locked. Press either of the following keys to unlock the

screen.

—

Problem Cause Solution Page

CAUTION

• This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the

upper threading is done, the machine will not operate properly. Also, depending on the pattern selected,

the machine may feed the fabric even if the needle is raised. This is due to the needle bar release

mechanism. At these times, the machine will make a sound different from that made during normal

sewing. This is not the sign of a malfunction.

• If the power is disconnected during sewing:

Turn the main power to OFF and unplug the machine.

If you restart the machine, follow the instructions for operating the machine correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is 4000 Seite 227

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info