Bedienungsanleitung Brother Innov-is 4500D (Seite 15 von 276) (Englisch)

613441

Zoom out

Zoom in

Vorherige Seite

1/276

Nächste Seite

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS

Embroidery Unit

a Carriage

The carriage moves the embroidery frame automatically when

embroidering.

b Release button (located under the embroidery unit)

Press the release button to remove the embroidery unit.

c Feed dog position switch

Use the feed dog position switch to raise and lower the feed

dogs while the embroidery unit is attached.

d Embroidery unit connection

Insert the embroidery unit connection into the connection port

when attaching the embroidery unit.

e Embroidery frame holder

Insert the embroidery frame into the embroidery frame holder to

hold the frame in place.

f Frame-securing lever

Press the frame-securing lever down to secure the embroidery

frame.

Operation Buttons

a “Start/Stop” button

Press this button and the machine will sew a few stitches at a

slow speed and then begin sewing at the speed set by the

sewing speed controller. Press the button again to stop the

machine. Hold the button in to sew at the machine’s slowest

speed. The button changes color according to the machine’s

operation mode.

b “Reverse/Reinforcement Stitch” button

Use this button to sew reinforcement stitches at the beginning

and end of sewing. Press this button, and the machine sews 3

stitches in the same spot and stops automatically. For straight

and zigzag stitch patterns that take reverse stitches, the

machine will sew reverse stitches at low speed only while

holding down the “Reverse/Reinforcement Stitch” button (the

stitches are sewn in the opposite direction).

c “Needle Position” button

Use this button when changing sewing direction or for detailed

sewing in small areas. Press this button to raise or lower the

needle position. Press the button twice to sew a single stitch.

d “Thread Cutter” button

Press this button after sewing to automatically trim the excess

thread.

e “Presser Foot Lifter” button

Press this button to lower the presser foot and apply pressure to

the fabric. Press this button again to raise the presser foot.

f Sewing Speed controller

Use this controller to adjust the sewing speed. Move the slide to

the left to sew at slower speeds. Move the slide to the right to

sew at higher speeds. Beginners should sew at a slow speed.

g “Automatic Threading” button

Use this button to automatically thread the needle.

CAUTION

• After the embroidery frame is set in the frame

holder, be sure the frame-securing lever is

correctly lowered.

Note

• Be sure that the feed dog position switch on

the embroidery unit is located at right when

embroidering.

• You can also sew utility/decorative stitches

with the embroidery unit attached. Set the

feed dog position switch on the embroidery

unit to the appropriate setting.

Green: the machine is ready to sew or is sewing.

Red: the machine cannot sew.

CAUTION

• Do not press the thread cutter button after the

threads have already been cut. Otherwise, the

needle may break, the threads may become

tangled, or damage to the machine may occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is 4500D Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is 4500D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info