Bedienungsanleitung Brother Innov-is A80 (Seite 62 von 72) (Englisch)

718715

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Troubleshooting

Remove any threads in the race and around the feed

dogs.

Turn the handwheel to raise the feed dogs.

Align the two screw holes in the needle plate with the

two holes at the needle plate mounting base, and then

fit the needle plate onto the machine.

Lightly finger-tighten the screw on the right side of the

needle plate. Then, use the disc-shaped screwdriver to

firmly tighten the screw on the left side. Finally, firmly

tighten the screw on the right side.

Turn the handwheel to check that the feed dogs move

smoothly and do not contact the edges of the slots in the

needle plate.

1 Correct position of feed dogs

2 Incorrect position of feed dogs

Insert the bobbin case by following step k in

“Cleaning the race” on page 55.

Attach the needle plate cover according to step l in

“Cleaning the race” on page 55.

Check the condition of the needle, and then install it.

If the needle is in a poor condition, for example, if it is

bent, be sure to install a new needle.

• Refer to “Checking the needle” on page 20 and

“Replacing the needle” on page 20.

■ Checking machine operations

If the needle plate has been removed, check machine

operations to confirm that installation has been completed

correctly.

Turn on the machine.

Select stitch .

Slowly turn the handwheel toward you

(counterclockwise), and look from all sides to check

that the needle falls at the center of the opening in the

needle plate.

If the needle contacts the needle plate, remove the

needle plate, and then install it again, starting with step

m in “Removing the fabric from the machine” on

page 59.

Select stitch . At this time, increase the stitch length

and width to their maximum settings.

• For details on changing the settings, refer to “Setting

the stitch width” on page 27 and “Setting the stitch

length” on page 27.

Slowly turn the handwheel toward you

(counterclockwise) and check that the needle bar and

feed dogs operate correctly.

If the needle or feed dogs contact the needle plate, the

machine may be malfunctioning; therefore, contact

your nearest Brother authorized service center.

Turn off the machine, and then install the bobbin and

presser foot.

Never use a scratched or damaged presser foot.

Otherwise, the needle may break, or sewing

performance may suffer.

• Refer to “Installing the bobbin” on page 14 and

“Replacing the presser foot” on page 21.

Correctly thread the machine.

• For details on threading the machine, refer to “Upper

Threading” on page 15.

Perform trial sewing with cotton fabric.

Memo

• Since the needle may have been damaged when the

fabric was caught in the machine, we recommend

replacing it with a new one.

Note

• Do not yet install the presser foot and thread.

1 Opening in the needle

plate

2 Handwheel

Note

• Incorrect sewing may be the result of incorrect upper

threading or sewing thin fabrics. If there are poor results

from the trial sewing, check the upper threading or the

type of fabric being used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is A80 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is A80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info