Bedienungsanleitung Brother Innov-is F460 (Seite 11 von 144) (Englisch)

718743

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Names of Machine Parts and Their Functions

GETTING READY

Basic operations B-3

Needle and presser foot section

1 Needle bar thread guide

Pass the upper thread through the needle bar thread guide.

2 Needle plate

The needle plate is marked with guides for sewing straight

seams.

3 Needle plate cover

Remove the needle plate cover to clean the bobbin case and

race.

4 Bobbin cover/bobbin case

Remove the bobbin cover, and then insert the bobbin into the

bobbin case.

5 Feed dogs

The feed dogs feed the fabric in the sewing direction.

6 Presser foot

The presser foot applies pressure consistently on the fabric as

the sewing takes place. Attach the appropriate presser foot for

the selected stitch.

7 Presser foot holder

The presser foot is attached onto the presser foot holder.

8 Presser foot holder screw

Use the presser foot holder screw to hold the presser foot in

place. (page B-32)

9 Buttonhole lever

Lower the buttonhole lever when sewing buttonholes and bar

tacks or when darning.

Operation buttons

1 “Start/Stop” button

Press the “Start/Stop” button to start or stop sewing. The

machine stitches at a slow speed at the beginning of sewing

while the button is pressed. When sewing is stopped, the

needle is lowered in the fabric. For details, refer to “STARTING

TO SEW” on page B-34.

The button changes color according to the machine’s

operation mode.

2 Reverse stitch button

For straight, zigzag, and elastic zigzag stitch patterns that use

reverse stitches, the machine will sew reverse stitches at low

speed only while holding down the Reverse stitch button. The

stitches are sewn in the opposite position.

For other stitches, use this button to sew reinforcement

stitches at the beginning and end of sewing. Press and hold

this button, and the machine sews 3 stitches in the same spot

and stops automatically. (page B-38)

3 Reinforcement stitch button

Use this button to sew a single stitch repeatedly and tie-off.

For character/decorative stitches, press this button to end with

a full stitch instead of at a mid-point. The LED light beside this

button lights up while the machine is sewing a full motif, and

automatically turns off when the sewing is stopped. (page B-

38)

4 Needle position button

Press the needle position button to raise or lower the needle.

Pressing the button twice sews one stitch.

5 Thread cutter button

Press the thread cutter button after sewing is stopped to cut

both the upper and the bobbin threads. For details, refer to

step

j under “Sewing a stitch” on page B-36.

6 Sewing speed controller

Slide the sewing speed controller to adjust the sewing speed.

Green: The machine is ready to sew or is sewing.

Red: The machine can not sew.

Orange: The machine is winding the bobbin thread, or

the bobbin winder shaft is moved to the right

side.

CAUTION

• Do not press (Thread cutter button) after

the threads have already been cut, otherwise

the needle may break, the threads may

become tangled or damage to the machine

may occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is F460 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is F460

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info