Bedienungsanleitung Brother Innov-is NV1040SE (Seite 103 von 120) (Englisch)

718767

103

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Troubleshooting

Appendix A-7

MAINTENANCE AND TROUBLESHOOTING

 Cause 2

A needle and thread appropriate for the fabric are not

being used.

The machine needle that should be used depends on the

type of fabric sewn and the thread thickness.

If a needle and thread appropriate for the fabric are not

being used, the thread tension will not be adjusted

correctly, causing wrinkles in the fabric or skipped

stitches.

• Refer to “Fabric/Thread/Needle Combinations” in the

“Basic operations” section to check that a needle and

thread appropriate for the fabric are being used.

 Cause 3

An appropriate upper tension is not selected.

The setting selected for the upper thread tension is not

appropriate.

Refer to “Setting the thread tension” in the “Basic

operations” section to select an appropriate thread

tension.

The appropriate thread tension differs depending on the

type of fabric and thread being used.

* Adjust the thread tension while test sewing on a

piece of scrap fabric that is the same as that used in

your project.

• If the bobbin thread is visible from the right side of

the fabric

Turn the thread tension dial to the left to decrease the

tension of the upper thread.

• If the upper thread is visible from the wrong side of

the fabric

Turn the thread tension dial to the right to increase

the tension of the upper thread.

Fabric is caught in the machine and cannot

be removed

If the fabric is caught in the machine and cannot be removed,

the thread may have become tangled under the needle plate.

Follow the procedure described below to remove the fabric

from the machine. If the operation cannot be completed

according to this procedure, instead of attempting to remove it

forcefully, contact your nearest Brother authorized service

center.

■ Removing the fabric from the machine

Immediately stop the machine.

Turn off the machine.

Remove the needle.

If the needle is lowered into the fabric, turn the

handwheel away from you (clockwise) to raise the

needle out of the fabric, and then remove the needle.

• Refer to “Replacing the needle” in the “Basic

operations” section.

Remove the presser foot and presser foot holder.

• Refer to “Replacing the presser foot” and “Removing

and attaching the presser foot holder” in the “Basic

operations” section.

Lift up the fabric and cut the threads below it.

If the fabric can be removed, remove it. Continue with

the following steps to clean the race.

Remove the needle plate cover.

1 Needle plate cover

• Refer to “Cleaning the race” on page A-2.

Cut out the tangled threads, and then remove the

bobbin.

Note

• If the upper threading and bobbin threading are

incorrect, the thread tension cannot be adjusted

correctly. Check the upper threading and bobbin

threading first, and then adjust the thread

tension.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is NV1040SE Seite 103

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is NV1040SE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info