Bedienungsanleitung Brother Innov-is NV1040SE (Seite 112 von 120) (Englisch)

718767

112

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Troubleshooting

A-16

High-pitched

sound while

sewing

Dust or lint is caught in the feed dogs. Remove the dust or lint. A-2

Pieces of thread are caught in the race. Clean the race. A-2

Upper threading is incorrect.

Check the steps for threading the machine and

rethread the machine.

B-20

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-14

There are needle holes or friction scratches in

the bobbin case.

Replace the bobbin case, or consult your

authorized Brother dealer.

A-2

Fabric does not

feed through the

machine.

Feed dogs are set in the down position.

Slide the feed dog position switch to the right

B-2

Stitches are too close together. Lengthen the stitch length setting. B-39

Wrong presser foot was used. Use the correct presser foot. B-31

Needle is turned, bent or the point is dull. Replace the needle. B-28

Thread is entangled.

Cut the entangled thread and remove it from the

race.

A-7

Zigzag foot “J” is slanted on a thick seam at the

beginning of stitching.

Use the presser foot locking pin (black button

on the left side) on zigzag foot “J” to keep the

presser foot level while sewing.

S-4

Presser foot pressure is set incorrectly for

fabric.

Adjust the presser foot pressure

within the settings screen.

B-42

The fabric feeds in

the opposite

direction.

The feed mechanism is damaged.

Contact your authorized Brother dealer or the

nearest Brother authorized service center.

–

The needle

contacts the

needle plate.

The needle clamp screw is loose.

Firmly tighten the needle clamp screw. If the

needle is bent or blunt, replace it with a new

one.

B-28

Needle is turned, bent or the point is dull. Replace the needle. B-28

Fabric being sewn

with the machine

cannot be

removed.

Thread is tangled below the needle plate.

Lift up the fabric and cut the threads below it,

and clean the race.

A-7

A broken needle

has fallen into the

machine.

–

Turn off the machine, and then remove the

needle plate. If the needle that fell into the

machine can be seen, use tweezers to remove

it. After removing the needle, return the needle

plate to its original position and insert a new

needle.

Before turning on the machine, slowly turn the

handwheel toward you to check that it turns

smoothly and that the new needle enters

through the center of the needle plate opening.

If the handwheel does not turn smoothly or the

needle that fell into the machine cannot be

removed, contact your authorized Brother

dealer or the nearest Brother authorized service

center.

A-7

The handwheel

feels sluggish

when it is turned.

Thread is tangled in the bobbin case.

Remove the tangled thread from the bobbin

case. Re-install the bobbin case so it is

correctly positioned.

A-5, A-7

Symptom Probable Cause Remedy Reference

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is NV1040SE Seite 112

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is NV1040SE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info