618042
162
Zoom out
Zoom in
Vorherige Seite
1/180
Nächste Seite
ADJUSTING THE THREAD TENSION
A-12
After embroidering trial patterns and checking the results, adjust the thread tensions if necessary. After adjusting the
tensions, be sure to embroider trial patterns again in order to check the results.
Adjusting the upper thread tension
We recommend a setting between 6 and 8 for the upper
thread tension when creating bobbin work.
Refer to “Adjusting Thread Tension” on page E-30.
Adjusting the tension of the bobbin
thread
If the desired stitching cannot be achieved after
adjusting the upper thread tension, adjust the tension of
the bobbin thread. The tension of the bobbin thread can
be adjusted by turning the slotted-head (–) screw on the
bobbin case (gray) for bobbin work.
a Do not turn the phillips screw (+).
b Adjust with a small screwdriver.
To increase the tension of the bobbin thread, turn the
slotted-head (–) screw 30° to 45° clockwise.
To decrease the tension of the bobbin thread, turn the
slotted-head (–) screw 30° to 45° counterclockwise.
ADJUSTING THE THREAD TENSION
Note
Turning the screw on the bobbin case (gray)
may push up the spring plate, as shown
below.
If this occurs, gently press down the spring
plate with a screwdriver so it is lower than
the top surface of the bobbin case (gray),
and then insert the bobbin case into the
machine.
a Spring plate
CAUTION
DO NOT adjust the position of the phillips (+)
screw on the bobbin case (gray) as this may result in
damage to the bobbin case, rendering it useless.
If the slotted-head screw (-) is difficult to turn, do
not use force. Turning the screw too much or
providing force in either (rotational) direction may
cause damage to the bobbin case. Should damage
occur, the bobbin case may not maintain proper
tension.
Note
If the bobbin thread tension is tight, the
thread cannot be passed through the
tension spring when the bobbin is installed
in the bobbin case. (Refer to “When tension
is not applied to the bobbin thread” on
page A-6.)
162

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother Innov-is V3 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Brother Innov-is V3

Brother Innov-is V3 Bedienungsanleitung - Deutsch - 180 seiten

Brother Innov-is V3 Bedienungsanleitung - Holländisch - 180 seiten

Brother Innov-is V3 Bedienungsanleitung - Französisch - 180 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info