618042
173
Zoom out
Zoom in
Vorherige Seite
1/180
Nächste Seite
ERROR MESSAGES
Maintenance and Troubleshooting
Appendix A-23
A
2
Not enough available memory to save the pattern. Delete
another pattern?
This message is displayed when the memory is full and the
pattern cannot be saved.
OK to automatically lower the presser foot?
This message is displayed when is pressed (the
presser foot is raised).
OK to delete the selected pattern? This message is displayed when the selected pattern is about
to be deleted.
OK to recall and resume previous memory? This message appears if the machine is turned off while
sewing, then turned on again.
Press to return the machine to the condition (pattern
position and number of stitches) when it was turned off. Follow
the procedure described in “If the Thread Breaks During
Sewing” on page E-27 to align the needle position and sew the
remainder of the pattern.
OK to reset the pattern’s border setting, position and/or angle? This message appears when you try to use the automatic
positioning function using the sensor pen with the pattern,
rotated or replaced, or with the border pattern. (see page B-58)
OK to revert to the original position and/or angle? This message appears when you try to use the automatic
positioning function using the sensor pen with the pattern,
rotated or replaced. (see page B-58)
Preventive maintenance is recommended. This message is displayed when the machine needs to be
maintained. (see page A-15)
Retrieving the pattern. Wait a moment. This message is displayed when the machine is retrieving a
previously saved pattern while in “Embroidery Edit” mode.
Sensor module error. This message appears when something is wrong with the
sensor unit of the machine. Consult your authorized dealer.
Set the clock. This message appears when the time/date is not set. Set
time/date. (see page B-18)
The bobbin thread is almost empty. This message is displayed when the bobbin thread is running
out.
The bobbin winder safety device has activated. Is the thread
tangled?
This message is displayed when the bobbin is being wound,
and the motor locks because the thread is tangled, etc.
The carriage of the embroidery unit will move. Keep your
hands etc. away from the carriage.
This message appears before embroidery unit moves.
The needle will move. Keep your hands etc. away from the
needle area.
This message appears when you touch the point closer than 2
cm from the needle drop point with the sensor pen in the
sensor function. (see page B-55)
The pattern extends out of the pattern area, repeat positioning
of center and angle using sensor pen.
This message appears when the specified pattern position
extends out of the pattern area. Specify more centered
position of the embroidery frame. (see page B-58)
The pockets are full. Delete a pattern. This message is displayed when the memory is full and a
pattern must be deleted.
The safety device has been activated.Is the thread tangled? Is
the needle bent?
This message is displayed when the motor locks due to
tangled thread or for other reasons related to thread delivery.
The shutoff support mode has been activated. Turn off the
machine.
This message appears when the machine is in the shutoff
support mode. Turn off the machine once to start the machine
again. (see page B-25)
The upper thread may not be threaded correctly. Thread the
upper thread from the beginning.
This message is displayed when it seems that the upper
thread has not been threaded correctly.
The USB media was changed. Do not change the USB media
while it is being read.
This message is displayed when you attempt to select a
pattern after the USB media in which the pattern is saved has
been changed.
There is no needle plate cover. Attach a needle plate cover. This message is displayed when the needle plate cover is not
attached.
This file cannot be used. This message appears if the file format is incompatible with
this machine. Check the list of compatible file formats. (see
page E-44)
Marks Error Messages Cause/Solution
173

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother Innov-is V3 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Brother Innov-is V3

Brother Innov-is V3 Bedienungsanleitung - Deutsch - 180 seiten

Brother Innov-is V3 Bedienungsanleitung - Holländisch - 180 seiten

Brother Innov-is V3 Bedienungsanleitung - Französisch - 180 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info