Bedienungsanleitung Brother Innov-is V5 (Seite 298 von 312) (Englisch)

618043

298

Zoom out

Zoom in

Vorherige Seite

1/312

Nächste Seite

TROUBLESHOOTING

A-32

High-pitched sound

while sewing

Dust or lint is caught in the feed dogs. Remove the dust or lint. A-19

Pieces of thread are caught in the race. Clean the race. A-19

Upper threading is incorrect. Check the steps for threading the machine

and rethread the machine.

B-44

There are scratches on the bobbin case. Replace the bobbin case, or consult your

authorized dealer.

A-19

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-41

Character pattern

does not turn out

Wrong presser foot was used. Attach the correct presser foot.

S-67

Pattern adjustment settings were set

incorrectly.

Revise the pattern adjustment settings. S-82

Did not use a stabilizer material on thin fabrics

or stretch fabrics.

Attach a stabilizer material. S-81

Thread tension is set incorrectly. Adjust the thread tension. S-12, E-30

Fabric was pulled, pushed or fed at an angle

while it was being sewn.

Sew while guiding the fabric with your hands

so that the fabric is fed in a straight line.

S-3

Machine does not

operate

There is no pattern selected. Select a pattern. S-21, S-77, E-3,

E-58

“Start/Stop” button was not pushed. Press the “Start/Stop” button. B-10

Main power switch is not turned on. Turn the main power to ON. B-17

Presser foot is not lowered. Lower the presser foot. B-10

“Start/Stop” button was pushed with the foot

controller attached.

Remove the foot controller, or use the foot

controller to operate the machine.

S-4

The “Start/Stop” button was pressed while the

machine is set for the sewing speed controller

to control the zigzag stitch width.

Use the foot controller instead of the

“Start/Stop” button to operate the machine,

or set the “Width Control” to “OFF” in the

settings screen.

B-24, S-4

All keys and buttons have been locked by

Press to unlock all keys and

buttons.

B-51, B-53

Nothing happens,

even if the LCD

display is pressed

The screen has been locked. Press either of the following keys to unlock

the screen.

—

The fabric feeds in the

opposite direction.

The feed mechanism is damaged. Contact your dealer or the nearest authorized

service center.

—

The LCD screen is

fogged up.

Condensation has formed on the LCD screen. After a while, the cloudiness will disappear. —

Embroidery pattern

does not sew out

correctly

Thread is twisted. Use scissors, etc., to cut the twisted thread

and remove it from the race, etc.

A-27

Fabric was not inserted into the frame correctly

(fabric was loose, etc.).

If the fabric is not stretched tight in the frame,

the pattern may turn out poorly or there may

be shrinkage of the pattern. Set the fabric

into the frame correctly.

E-14

Stabilizing material was not attached. Always use stabilizing material, especially

with stretch fabrics, lightweight fabrics,

fabrics with a coarse weave, or fabrics that

often cause pattern shrinkage. See your

authorized dealer for the proper stabilizer.

E-11

There was an object placed near the machine,

and the carriage or embroidery frame hit the

object during sewing.

If the frame bumps something during sewing,

the pattern will turn out poorly. Do not place

anything in the area where the frame may

bump it during sewing.

E-21

Fabric outside the frame edges interferes with

the sewing arm, so the embroidery unit cannot

move.

Reinsert the fabric in the embroidery frame so

that the excess fabric is away from the

sewing arm, and rotate the pattern 180

degrees.

E-14

Fabric is too heavy, so the embroidery unit

cannot move freely.

Place a large thick book or similar object

under the arm head to lightly lift the heavy

side and keep it level.

—

Problem Cause Solution Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is V5 Seite 298

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is V5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info