631248
79
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
77
3
Reinforcement Stitching
Reinforce points that will be subject to strain, such as sleeve holes, inseams and pocket corners.
Pattern numbers vary depending on the machine model. Check the pattern numbers available with your
machine, and select the desired stitch.
The values below “Auto” are set when the pattern is selected. The setting can be adjusted to any value within the range
indicated below “Manual”.
Triple stretch stitching
With each stitch, three overlapping stitches are
sewn.
a
Turn on the machine.
b
With the pattern selection dial,
select stitch .
c
Attach zigzag foot “J”.
For details, refer to “Replacing the presser
foot” (page 33).
d
Start sewing.
Changing the needle position
The needle position can be adjusted with the
straight stitch (left needle position) and the triple
stretch stitch by adjusting the stitch width. Press
the “–” side of the stitch width key for a left
needle position, or press the “+” side for a right
needle position.
a Stitch width
b Stitch width key
c Moves the needle position to the left
d Moves the needle position to the right
Stitch Name
Pattern
Presser Foot
Pattern No.
Application
Stitch Width
[mm (inch)]
Stitch Length
[mm (inch)]
Twin Needle
Walking Foot
Reverse/
Reinforcement
Stitching
70 stitches
model
60 stitches
model
50 stitches
model
40 stitches
model
Auto Manual Auto Manual
Triple stretch
stitch
J03030303
Attaching sleeves,
sewing inseams, sew-
ing stretch fabrics
and decorative stitch-
ing
0.0
(0)
0.0–7.0
(0–1/4)
2.5
(3/32)
1.5–4.0
(1/16–3/16)
Yes
(J)
No
Reinforcement
Bar tack
stitch
A44443835
Reinforcing open-
ings and areas where
the seam easily
comes loose
2.0
(1/16)
1.0–3.0
(1/16-1/8)
0.4
(1/64)
0.3–1.0
(1/64-1/16)
No No
Automatic
Reinforcement
Before replacing the presser foot, be sure to turn off the sewing machine, otherwise injuries may occur if a
button is accidentally pressed and the machine starts sewing.
CAUTION
dc
ab
79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother JK7000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info