Bedienungsanleitung Brother KE20 (Seite 28 von 72) (Englisch)

718836

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

SEWING BASICS

Take your foot off the foot controller, or press

(start/stop button) once (if the machine was

started by pressing (start/stop button)) (for

models equipped with the start/stop button).

 The machine stops sewing.

Raise the needle by turning the handwheel

toward you (counterclockwise) so that the mark

on the wheel points up. (With models equipped

with (needle position button), raise the

needle by pressing once or twice.)

This procedure is not necessary if the needle stop

position has been set to the raised position

(page 9).

Raise the presser foot lever.

Pull the fabric to the left side of the machine,

and then cut the threads by using the thread

cutter.

Memo

● When the foot controller is plugged in, start/stop

button cannot be used to start sewing (for models

equipped with the start/stop button).

●

When sewing is stopped, the needle remains

lowered (in the fabric). The machine can be set so

that the needle will stay up when sewing is stopped.

For details on setting the machine so that the

needles stay up when sewing is stopped, refer to

“Changing the needle stop position” (page 9).

■ Sewing reinforcement stitches

When sewing stitches other than straight or zigzag

stitches that are secured with reverse stitching,

pressing (reverse/reinforcement stitch button)

sews reinforcement stitches, 3 to 5 stitches on top of

each other.

Memo

● Whether reverse stitches or reinforcement stitches

are sewn depends on the stitch that is selected. For

details, refer to “STITCH SETTINGS” (page 50).

The thread tension will affect the quality of your stitches. You

may need to adjust it when you change fabric or thread.

Memo

● We recommend that you do a test sample on scrap

of a fabric before you start to sew.

■ Correct tension

Correct tension is important as too much or too little tension

will weaken your seams or cause puckers on your fabric.

■ Upper tension is too tight

Loops will appear on the surface of the fabric.

Note

●

If the bobbin thread was incorrectly threaded, the upper

thread may be too tight. In this case, refer to “Lower

threading” (page 13) and rethread the bobbin thread.

Solution

Reduce the tension by turning the upper

tension-control dial to a lower number.

Memo

●

When you finish sewing, remove the bobbin cover and then

make sure that the thread is shown as below. If the thread is

not shown as below, the thread is not inserted through the

tension-adjusting spring of the bobbin case correctly. Reinsert

the thread correctly. For details, refer to page 13, 14.

a Thread cutter

a Reverse stitching

b Reinforcement stitching

Thread tension

a Wrong side

b Surface

c Upper thread

d Lower thread

a Wrong side

b Surface

c Upper thread

d Lower thread

e Loops appear on

surface of fabric

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother KE20 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother KE20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info