451205
27
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
27
For Wireless Network Users
Wireless Network
17
Configure the wireless
settings using the
automatic wireless (one-
push) method
a Confirm your wireless access point/router has
the SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™ symbol as shown below.
b Place the Brother machine within range of your
SecureEasySetup™, Wi-Fi Protected Setup or
AOSS™ access point/router. The range may
differ depending on your environment. Refer to
the instructions provided with your access
point/router.
c Push the SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™ button on your wireless
access point/router.
See the user’s guide for your wireless access
point/router for instructions.
d On your machine, press Menu.
Press 5 to choose 5.Network.
Press 3 to choose 3.SES/WPS/AOSS.
When WLAN Enable ? is displayed, press 1
to accept.
This will start the wireless setup wizard.
This feature will automatically detect which
mode (SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™) your access point/router
uses to configure your machine.
e If the LCD shows Connected, the machine
has successfully connected to your wireless
access point/router. You can now use your
machine in a wireless network.
If the LCD shows Setting WLAN, then
Connection Error, a session overlap was
detected. The machine has detected 2 or more
wireless access points/routers on your network
that have the SecureEasySetup™, Wi-Fi
Protected Setup mode or AOSS™ mode
enabled. Make sure that only one wireless
access point/router has one of these modes
enabled and try starting from c again.
If the LCD shows Setting WLAN, then No
Access Point, the machine has not detected
the access point/router on your network with
the SecureEasySetup™, Wi-Fi Protected
Setup or AOSS™ mode enabled. Move your
machine close to the access point/router and
try starting from c again.
If the LCD shows Setting WLAN, then
Connection Fail, the machine has not
successfully connected to your wireless access
point/router. Try starting from c again. If the
same message is indicated again, reset the
machine back to the default factory settings
and try again. For resetting, see Restore the
network settings to factory default on page 39.
f Press OK.
Note
If your wireless access point/router supports
Wi-Fi Protected Setup (PIN Method) and you
want to configure your machine using the PIN
(Personal Identification Number) Method, see
Using the PIN Method of Wi-Fi Protected Setup in
the Network User’s Guide on the CD-ROM.
LCD messages when using the
SES/WPS/AOSS control panel menu
Setting WLAN Searching for or accessing the
access point, and
downloading settings from the
access point.
Connecting
SES/WPS/AOSS
Connecting to the access
point.
Connected The machine has successfully
connected.
Connection
Error
A session overlap was
detected.
No Access
Point
The access point detection
failed.
Connection
Fail
Connection failed.
The machine was not able to
connect with the access point.
Try the configuration from c on
page 27 again.
Note
You can also manually configure the wireless
settings following the steps starting at step 16-a
on page 25.
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

brother-mfc-255cw

Suche zurücksetzen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother MFC-255CW wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Brother MFC-255CW

Brother MFC-255CW Bedienungsanleitung - Deutsch - 163 seiten

Brother MFC-255CW Installationsanweisung - Deutsch - 40 seiten

Brother MFC-255CW Bedienungsanleitung - Englisch - 159 seiten

Brother MFC-255CW Installationsanweisung - Holländisch - 40 seiten

Brother MFC-255CW Bedienungsanleitung - Holländisch - 163 seiten

Brother MFC-255CW Bedienungsanleitung - Französisch - 167 seiten

Brother MFC-255CW Installationsanweisung - Französisch - 40 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info