Bedienungsanleitung Brother MFC-6490CW (Seite 26 von 42) (Englisch)

451226

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

For Wireless Network Users

Connecting the Brother machine to the wireless network

Configure the wireless

settings (typical Wireless

Setup in infrastructure

mode)

a On your machine, press Menu.

Press a or b to choose Network and press

OK.

Press a or b to choose WLAN and press OK.

Press a or b to choose Setup Wizard and

press OK.

When Network I/F switched to

Wireless is displayed, press OK to accept.

This will start the wireless setup wizard.

To cancel, press Stop/Exit.

b The machine will search for available SSIDs. If

a list of SSIDs is displayed, use the a or b keys

to choose the SSID you wrote down in step

15-a on page 25, then press OK. If you are

using an authentication and encryption method

that requires a password, go to c.

If your authentication method is Open System

and your encryption mode is None, go to d.

If your access point is set to not broadcast the

SSID you will have to manually add the SSID

name. For details, see the Network User’s

Guide on the CD-ROM.

c Enter the Password you wrote down in

step 15-a on page 25 using the dial pad to

choose each letter or number.

You can use the d and c keys to move the

cursor left and right. For example, to enter the

letter a, press the 2 key on the dial pad once.

To enter the number 3, press the 3 key on the

dial pad seven times.

The letters appear in this order: lower case,

upper case and then numbers.

(For more information, see Entering Text for

Wireless Settings on page 41.)

Press OK when you have entered all the

characters, then press 1 for Yes to apply your

settings. Go to d.

d Your machine will now try to connect to your

wireless network using the information you

have entered. If successful, Connected will

appear for 60 seconds on the LCD.

It may take a few minutes to connect to your

wireless network.

e Press OK.

Wireless setup is now complete. A four

level indicator at the top of your

machine’s LCD will show the wireless

signal strength of your access

point/router.

Note

It will take several seconds to display a list of

available SSIDs.

If a list of SSIDs is not displayed, make sure your

access point is on. Move your machine closer to

the access point and try starting from a again.

Note

If the LCD displays Wrong Password, the

password you entered did not match with your

access point. Verify your network settings

collected in step 15-a on page 25, then repeat a

to c to make sure you have entered the correct

information.

If the LCD displays Connection Failed, make

sure your access point is on, and verify your

network settings collected in step 15-a on

page 25. Temporarily move your machine as

close as possible to the access point, then repeat

a to c to make sure you have entered the correct

information.

If your access point does not have DHCP enabled

you will need to manually configure the IP

address, subnet mask and gateway of the

machine to suit your network. See Chapter 6 of

the Network User’s Guide for details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother MFC-6490CW Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother MFC-6490CW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info