Bedienungsanleitung Brother MFC-7820N (Seite 87 von 152) (Englisch)

451267

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Troubleshooting and routine maintenance

11 - 2

Document Jam The document was not inserted or fed

properly, or the document scanned from

the ADF was too long.

See Document jams on page 11-6.

See Using the automatic document feeder (ADF) on

page 1-7.

Drum Error The drum unit needs to be cleaned. See Cleaning the corona wire on page 11-24.

Fail to Warm up The fuser unit is too cold. (For MFC-7420)

When you turn off the machine’s power switch its

memory will be cleared. (To check if faxes are in the

machine’s memory, see Checking if the machine has

faxes in its memory on page 11-5.) If there are faxes,

you need to save them before following the

suggestions below. (To save the faxes, see

Transferring faxes to your PC on page 11-5 or

Forwarding faxes to another fax machine on page

11-5.)

Then, turn off the machine’s power switch. Check the

machine’s environment. If it is in a location that is too

hot or too cold, try to cool or warm the room by turning

on the air conditioner or heater. Or, move the machine

to another location. Then, turn on the machine’s power

switch.

(For MFC-7820N)

Turn off the machine’s power switch, and check the

machine’s environment. If it is in a location that is too

hot or too cold, try to cool or warm the room by turning

on the air conditioner or heater. Or, change the

location. Then, turn on the machine’s power switch.

(The machine can be turned off for up to 4 days without

losing faxes stored in the memory.)

Unit is too Hot The fuser unit is too hot.

Machine too Hot The inside of the machine is too hot. Listen to the machine to check that the cooling fan is

spinning.

Make sure that the air vents are not covered up or

blocked.

If the fan is spinning and air vents are clear, you should

let the machine cool down for several minutes before

using it again.

If the fan is not spinning, you need to save the faxes

before you follow the suggestions below.

(For MFC-7420)

When you turn off the machine's power switch its

memory will be cleared. To check whether the

machine has faxes in its memory see Checking if the

machine has faxes in its memory on page 11-5. If there

are faxes you need to save them before following the

suggestions below. (See Transferring faxes to your PC

on page 11-5 or Forwarding faxes to another fax

machine on page 11-5.)

Turn off the machine's power switch and then on

again. If the error message continues, leave the

machine for several minutes and try it again.

(For MFC-7820N)

Turn off the machine's power switch and then on

again. If the error message continues leave the

machine for several minutes and then try it again. (The

machine can be turned off for up to 4 days without

losing faxes stored in the memory.)

ERROR MESSAGES

ERROR MESSAGE CAUSE ACTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother MFC-7820N Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother MFC-7820N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info