Bedienungsanleitung Brother MFC-9330CDW (Seite 27 von 42) (Englisch)

585303

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

For Wireless Network Users

Wireless Network

Windows

Macintosh

Manual setup from the control panel using the Setup Wizard

(Windows

, Macintosh and mobile devices)

Set up the wireless

settings

a On your machine, press .

Press Setup Wizard.

b When Enable WLAN? is displayed, press

Yes. This will start the wireless setup wizard.

c The machine will search for available SSIDs. It

will take a few minutes to display a list of

available SSIDs.

If a list of SSIDs is displayed, swipe up or down,

or press a or b to choose the SSID you wrote

down in step 16-b on page 23.

Press OK.

d Do one of the following:

 If the wireless access point/router of the

selected SSID supports WPS and the

machine asks to use WPS, go to e.

 If you are using an authentication and

encryption method that requires a Network

Key, go to f.

 If your authentication method is Open

System and your encryption mode is None,

go to g.

e To connect your machine using the automatic

wireless mode, press Yes. (If you choose

No (Manual), go to f to enter the Network

Key.) When the Touchscreen instructs you to

start WPS, press the WPS button on your

wireless access point/router, and then press

Next on the Touchscreen. Go to g.

f Enter the Network Key you wrote down in step

16-b on page 23 using the numbers and

characters on the Touchscreen.

Press OK when you have entered all the

characters, and then press Yes to apply your

settings.

g Your machine will now try to connect to your

wireless network using the information you

have entered.

A connection result message appears on the

Touchscreen and a WLAN report will

automatically print.

If the connection failed, check the error code on

the printed report and refer to Troubleshooting

uu page 30.

Press OK.

IMPORTANT

You must have the wireless settings you wrote

down for your network in step 16-b on page 23

before you proceed.

NOTE

If you use your machine in an IEEE 802.1x

supported wireless network: uu Network User's

Guide: Using IEEE 802.1x authentication.

NOTE

• If the list is blank, check that the wireless access

point/router has power and is broadcasting the

SSID. Move your machine closer to the wireless

access point/router and try starting from a

again.

• If your wireless access point/router is set to not

broadcast the SSID you will have to manually

add the SSID name. For details: uu Network

User's Guide: Configuring your machine when

the SSID is not broadcast.

NOTE

• To enter numbers or special characters, press

repeatedly until the character you want to

enter appears, then press the character you

want.

• If you entered a character incorrectly and want

to change it, press d or c to move the cursor to

the incorrect character, then press .

• To enter a space, press Space.

• For more details, see Entering Text uu

page 33.

Wireless setup is now complete.

A four-level indicator at the top right of

your machine’s Touchscreen will show

the wireless signal strength of your

wireless access point/router.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother MFC-9330CDW Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother MFC-9330CDW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info