Bedienungsanleitung Brother NX-2000 (Seite 11 von 164) (Englisch)

463656

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS

Machine

■ Front View

a Top cover

Open the top cover to thread the machine and wind the bobbin.

b Thread guide plate

Pass the thread around the thread guide plate when threading

the upper thread.

c Thread take-up lever check window

Look through the window to check the position of the take-up lever.

d Needle threader lever

Use the needle threader lever when threading the needle

automatically.

e Thread cutter

Pass the threads through the thread cutter to cut them.

f Flat bed attachment with accessory compartment

Store presser feet and bobbins in the accessory compartment

of the flat bed attachment. Remove the flat bed attachment

when sewing cylindrical pieces such as sleeve cuffs.

g Operation buttons (5 buttons) and sewing speed

controller

Use these buttons to perform various operations, such as

starting sewing and raising or lowering the needle.

Slide the sewing speed controller to adjust the sewing speed

while using utility stitches.

h Knee lifter slot

Insert the knee lifter into the slot.

i Knee lifter

Use the knee lifter to raise and lower the presser foot.

j LCD (liquid crystal display)

Stitch settings can be viewed and edited, and operations for

using the machine can be displayed, and error messages

appear in the LCD.

k Spool pin

Place a spool of thread on the spool pin.

l Spool cap

Use the spool cap to hold the spool in place.

m Bobbin winder

Use the bobbin winder when winding the bobbin.

n Supplemental spool pin

Use this spool pin to wind the bobbin thread while sewing or to

sew with the twin needle.

o Thread guide

Pass the thread through this thread guide when winding the

bobbin thread.

p Bobbin winding thread guide

Pass the thread around this thread guide when winding the

bobbin thread.

■ Right-side/Rear View

a Handle

When transporting the machine, carry it by this handle.

b Handwheel

Turn the handwheel toward you to sew one stitch or to raise or

lower the needle.

c USB connector

Plug in a USB cable to connect a computer.

d Touch pen holder

Use the touch pen holder to hold the touch pen when it is not

being used.

e Foot controller jack

Insert the plug on the end of the foot controller cord into the foot

controller jack.

f Foot controller

Press the foot controller to control the speed of the machine.

g Jack connector

Insert the power cord into the jack connector.

h Main power switch

Use the main power switch to turn the machine ON and OFF.

i Air vent

Do not cover the air vent while the sewing machine is being

used.

j Feed dog position indicator

Indicates whether the feed dogs are raised or lowered.

k Presser foot lever

Raise and lower the presser foot lever to raise and lower the

presser foot.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother NX-2000 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother NX-2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info