Bedienungsanleitung Brother P-Touch QL 550 (Seite 7 von 19) (Englisch)

542758

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

STEP

IntroductionGetting startedMaintenance and

Troubleshooting

The Printer

• Never disassemble the printer or allow it to get wet to avoid possible fire or electrical

shock. Do not remove the power cord from or insert it into the electrical socket with wet

hands. Doing so could cause an electrical shock or fire.

• Do not touch the cutter. Personal injury could result. Take special care when changing

the cutter unit.

• The printer is a precision machine. Do not drop, hit or otherwise bang the printer.

• Do not lift the printer by the DK Roll compartment cover. The cover could come off and

the printer could fall and become damaged.

• The printer may malfunction if left near a television, radio, etc. Do not use the printer near

any machine that can cause electromagnetic interference.

• Do not expose the printer to direct sunlight or near heaters or other hot appliances, in

any location exposed to extremely high or low temperatures, high humidity or dusty

locations. Doing so could cause the machine to malfunction.

• Do not use paint thinner, benzene, alcohol or any other organic solvents to clean the

printer. Doing so may cause damage to the surface finish. Use a soft, dry cloth to clean

the printer.

• Do not place any heavy objects or objects containing water on top of the printer. If water

or any foreign object enters the printer, contact the retail outlet where the printer was

purchased or your local authorized service centre. If you continue to use the printer with

water or a foreign object in the printer, the printer may be damaged or personal injury

could result.

• Do not insert any objects into or block the label output slot, or USB port.

• Do not place any metal parts near the print head. The print head becomes very hot

during use and remains very hot immediately after use. Do not touch it directly with your

hands.

• Use only the interface cable (USB cable) included with the printer.

• Do not attempt to print labels while the DK Roll cover is open.

• If a paper jam should occur due to a build up of adhesive on the paper guide surface,

unplug the power cord from the electrical socket and wipe away the adhesive buildup on

the paper guide surface with a cloth dipped in ethanol or isopropyl (rubbing) alcohol. It is

recommended that you clean the paper guide when replacing the cutter unit. Refer to

"Replacing the cutter unit" on page 13.

Cutter unit

• The cutter unit contains a very sharp blade. To

prevent injury from a broken cutter blade:

• Make sure the top cover is closed when using

the cutter unit.

• Don't apply too much pressure when fitting or

removing the cutter unit.

• When the cutter unit becomes blunt you

should replace it with a new one.

• If you break the cutter unit, unplug your printer

from the power socket and remove the cutter

unit carefully with a pair of tweezers.

General Precautions

Paper guide surface

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother P-Touch QL 550 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother P-Touch QL 550

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info