Bedienungsanleitung Brother PE-DESIGN 3.0 (Seite 15 von 224) (Englisch)

631412

Zoom out

Zoom in

Vorherige Seite

1/224

Nächste Seite

Before Using Design Center Layout & Editing File Utility

Programmable

Stich Creator

Contents

Quik Reference Alphabetic IndexGetting Started

When Satin stitch is used in a wide area, the stitched area may shrink after sewing, depending on the

material and the type of thread used. When this happens, switch to this alternate method: Select Fill

stitch and use a stabilizer material on the reverse side of the fabric.

Note: When using Satin stitch in a wide area, the needle may move out of position by about 10 mm with

some machines. To avoid this, use the above mentioned alternate method.

To limit shrinking, set the stitch direction perpendicular to the larger edge of the area.

After creating an embroidery pattern made of several different parts (in Design Center or Layout & Edit-

ing), make sure that you check the sewing order and correct it if necessary.

With Design Center, the default sewing order is the order in which the sewing attributes are set.

With Layout & Editing, the default sewing order is the order in which the elements are drawn.

There are two ways of enlarging or reducing an imported embroidery pattern in Layout & Editing. You

may choose to simply scale your pattern with the selection cursor or apply the Stitch to Block function to

the pattern and then scale it.

When you scale an imported pattern, the number of stitches that will be sewn remain the same, resulting

in a change of embroidery quality if the size of the pattern is greatly changed.

Selecting the Sew – Stitch to Block command, then scaling a pattern allows you to keep the original

embroidery quality of the pattern, as the number of stitches that will be sewn automatically adapt to the

new size. Selecting the “Normal” sensitivity setting of the Stitch to Block function will allow you to main-

tain the embroidery quality in most cases. Selecting a ﬁner density setting in the Stitch to Block Sensitiv-

ity dialog will allow you to obtain a more complex embroidery; selecting a coarser density will create a

simpler embroidery.

When a pattern is scaled only moderately, it may not be necessary to apply the Stitch to Block function.

This system allows you to create a wide variety of embroidery patterns and supports wider ranges for

the setting of the sewing attributes (thread density, sewing pitch, etc.). However, the ﬁnal result also

depends on your particular sewing machine model. We recommend that you make a trial sewing sam-

ple with your sewing data before sewing on the ﬁnal material. Remember to sew your trial sample on

the same fabric, using the same needle and the same machine embroidery thread as your ﬁnal mate-

rial.

Tips and Techniques for Creating Embroidery Patterns

Data

After sewing

Shrinking more likely to occur

Shrinking less likely to occur

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother PE-DESIGN 3.0 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info