Bedienungsanleitung Brother PR-670E (Seite 224 von 244) (Englisch)

718890

224

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

222

The upper thread comes out of the needle when

embroidering begins.

If a short length of thread remains after the

thread is trimmed, the needle may become

unthreaded when embroidering begins again.

• Set the remaining length of thread to “Long

Tail” on the second page of the settings

screen.

p.185

The upper thread does not reach the bobbin thread when

embroidering begins.

There is no more thread in the bobbin, the

thread does not feed from the bobbin, or the

thread that is fed from the bobbin is too short.

• Correctly thread the lower thread.

p.33

Although the thread is not broken, a broken thread error

occurs and the machine stops.

If the thread breakage sensor in the thread

tension disc of the thread tension knobs cannot

detect that the thread is being fed, even if the

machine is running, a broken thread error

occurs and the machine is stopped. If the thread

came out of the thread tension disc, even

though the thread is not broken, the machine

detects that the thread is not being fed and

stops.

• Clean the tension unit. Correctly pass the

thread through the thread tension disc. If the

broken thread error occurs after the machine

is cleaned and rethreaded, the sensor may be

damaged. Consult your nearest authorized

Brother dealer.

p.52

p.213

The thread is worn.

Lint or dust has accumulated in the thread

tension disc.

• Remove the tension dials, and then remove

any lint or dust accumulated between the felt

washers.

p.213

Jumpstitches are long.

Lint or dust has accumulated in the thread

tension disc.

• Remove the tension dials, and then remove

any lint or dust accumulated between the felt

washers.

p.213

There are needle cuts or holes in the garment.

The needle is dull.

• Replace the needle. Dull needles have a

difficult time passing through the garment,

causing fabrics to tear.

p.30

p.79

The fabric is too delicate.

• The simple penetration of the needle could

damage delicate fabrics. Use stabilizer on top

of fabric.

p.204

Symptom

Probable Cause/Remedy Page

There is puckering in the fabric.

The thread tension is too tight.

• Adjust the tension according to the type of

fabric and thread being used. Polyester

thread will stretch during sewing especially if

the tensions are set too high. After the

stitching is complete, the thread returns to its

original strength, causing puckers in the

fabric.

p.103

The framing tension of the fabric is incorrect.

• Tightly frame non-stretchable, woven fabrics.

Loose framing will cause the fabric to bunch

up under the stitching.

Tautly frame soft knits using a stable backing.

Overstretching the garment will cause it to

look puckered when the frame is removed.

p.203

The column stitches are too long.

• Re-digitize the design with fill stitching or

with multiple rows of column stitching.

–

There is puckering in the fabric.

The needle is dull.

• Dull needles push fabric down and damage

material. Replace the needle.

p.30

p.79

The design density is too heavy.

• Too many stitches in an area pull fabric,

causing it to pucker. Slightly decrease the

design density by 5% to 10%.

p.184

The LCD cannot be read.

The LDC screen is too bright or too dark.

• Adjust the brightness of the screen display.

p.179

When embroidering thick fabric, the fabric cannot be

correctly hooped.

Fabric slips within the frame because of its

thickness.

• Wrap masking tape or bias tape around the

outer frame. The tape will provide resistance

so that the fabric does not easily slip.

p.203

CAUTION

• This machine is equipped with a thread

detecting mechanism. If the machine is not

threaded with the upper thread, the machine

will not operate correctly, even if the start/

stop button is pressed after unlocking the

machine.

• If the machine suddenly stops:

• Turn off the machine, and unplug the power

cord.

• Restart the machine with the correct operat-

ing procedure. Refer to page 35.

Symptom

Probable Cause/Remedy Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother PR-670E Seite 224

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother PR-670E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info