718477
36
Zoom out
Zoom in
Vorherige Seite
1/153
Nächste Seite
Setting Up the Printer
27
1
Infrastructure Mode 1
Infrastructure Mode allows you to connect the printer to a computer or mobile device via a Wi-Fi access
point/router.
Before You Begin
First you must configure the Wi-Fi settings of your printer to communicate with your Wi-Fi access
point/router. After the printer is configured, computers or mobile devices on your network will have access
to the printer.
Important
If you are going to connect the printer to your network, we recommend that you contact your system
administrator prior to installation. You must confirm your Wi-Fi settings before you proceed with this
installation.
To configure the Wi-Fi settings again, or if the status of the Wi-Fi connection for your printer is unknown,
reset the Wi-Fi settings of the printer.
1 Press and hold the (Power) button to turn the printer off.
2 Press and hold the (Feed) button and the (Power) button for about three seconds. The LED
indicator starts blinking in green.
3 While pressing the (Power) button, press the (Feed) button twice.
4 Release the (Power) button.
Note
To achieve the best results with normal everyday document printing, use the printer as close to the Wi-Fi
access point/router as possible with minimal obstructions. Large objects and walls between the two
devices as well as interference from other electronic devices can affect the data transfer speed of your
documents.
Connecting the printer to your Wi-Fi access point/router
1 First, write down the SSID (network name) and password (network key) of your Wi-Fi access
point/router.
2 Connect the printer and computer with a USB cable.
3 On your printer, press the [Menu], [ ] button to select the [WLAN] menu, and then press the [OK]
button.
Set [On/Off] to [On].
4 Configure the Infrastructure Mode settings of the printer.
Using your printer
1 On your printer, press the [Menu], [ ] button to select the [WLAN] menu, and then press the [OK]
button.
2 Press the [ ] button to select the [Mode] menu, and then press the [OK] button.
3 Select [Infrastructure], and then press the [OK] button.
36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother RJ-2150 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Brother RJ-2150

Brother RJ-2150 Bedienungsanleitung - Deutsch - 155 seiten

Brother RJ-2150 Bedienungsanleitung - Holländisch - 153 seiten

Brother RJ-2150 Bedienungsanleitung - Französisch - 153 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info