Bedienungsanleitung Brother X55 (Seite 4 von 4) (Englisch)

555747

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

To secure the stitching, turn the

material 90 degrees counterclockwise

and sew straight stitches to the end of

the front bar tack of the buttonhole.

After sewing the left side of the

buttonhole, stitch the right side and

observe the feeding.

If the left side is too open or tight

compared with the right side, adjust the

buttonhole ne-adjustment screw.

Left side

This

adjustment

ensures both

sides of the

buttonhole

are the same.

Turn the buttonhole ne-adjustment screw

with a large screwdriver as indicated in the

illustrations, according to the buttonhole

appearance.

Remove the material from the

machine. We recommend that you

put pins across both ends of the

buttonhole to prevent the stitches from

being cut.

Cut an opening in the middle of the

buttonhole with the seam ripper tool.

Be careful not to cut through and

stitches.

Securing the

Stitching and

Cutting the

Buttonhole

CAUTION

When using the seam ripper to open the

buttonhole, do not put your hand or nger

in the path of the ripper. The seam ripper

may slip and you may be injured.

CAUTION

Never use a bobbin case that is ●

scratched; otherwise the upper thread

may become tangled, the needle may

break, or sewing performance may

suffer. For a new bobbin case (part

code: XE9326-001), contact your nearest

authorized service center.

Make sure that you t the bobbin case ●

properly, otherwise the needle may

break.

Maintenance

Precautions on storing the machine

Cleaning

Restrictions on oiling

In order to prevent damaging this machine, it must not be oiled by the user.

This machine was manufactured with the necessary amount of oil applied to ensure

correct operation, making periodic oiling unnecessary.

If problems occur, such as difculty turning the handwheel or an unusual noise,

immediately stop using the machine, and contact your authorized dealer or the nearest

authorized service center.

Exposed to extremely high temperatures•

Exposed to extremely low temperatures•

Exposed to extreme temperature •

changes

Exposed to high humidity or steam•

Near a ame, heater or air conditioner•

Outdoors or exposed to direct sunlight•

Exposed to extremely dusty or oily •

environments

Note

In order to extend the life of this machine, periodically turn it on and use it. Storing this ●

machine for an extended period of time without using it may reduce its efciency.

Do not store the machine in any of the locations described below, otherwise damage to

the machine may result, for example, rust caused by condensation.

CAUTION

Make sure you unplug the machine before

you clean it, otherwise you risk getting an

electric shock or being injured.

Mark on the wheel points up to rise the

needle

Clean the race

Adjusting buttonholes

Making a buttonhole

Match up the

bar tack mark

to the two red

lines on the

presser foot.

Line the chalk

mark under the

center of the

presser foot.

Step Sewn section Pattern

Step 1

(Front bar

tack)

1. Set the pattern selection dial to “a”.

2. Lower the presser foot and sew 5 to 6

stitches.

3. Stop the machine when the needle is

at the left side of the stitches and then

raise the needle from the material.

Step 2

(Left side)

1. Turn the pattern selection dial to “b”.

2. Sew the length of the tailor’s chalk line.

3. Stop the machine when the needle is at

the left side of the stitch and then raise

the needle.

Step 3

(Back bar

tack)

1. Turn the pattern selection dial to “c”

(same position as in step 1).

2. Sew 5 to 6 stitches.

3. Stop the machine when the needle is at

the right side of the stitch and then raise

the needle from the material.

Step 4

(Right side)

1. Set the pattern selection dial to “d”.

2. Sew the right side until the needle

reaches the stitches sewn in step 1.

CAUTION

Always turn off the machine before replacing the presser foot. Otherwise, injuries may occur

if the foot controller is accidentally pressed and the machine starts sewing.

Sewing Buttonholes and Buttons

Preparation

Using tailor’s chalk, mark the

position and length of the buttonhole

on the fabric.

Buttonhole sewing

Push the frame

back until it stops

with the plastic

insert at the front

of the frame.

Attach the buttonhole foot.

CAUTION

If the presser foot is not installed

with the correct orientation, the

needle may strike the presser

foot, which may bend or break the

needle and cause injury.

XF4097-001.indd 2 4/11/2012 5:56:18 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother X55 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother X55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info